AR-M550 (serv.man15). (8) Simulation - Sharp Copying Equipment Service Manual (repair manual). Page 84

AR-M550/M620  SIMULATION  8 - 84

Touch the four cross marks (+) sequentially. The coordinates of
pressed positions are set.

When the coordinates setting is completed normally, the display turns
gray. When all the four points are set, the display returns to the normal
state.

When the touch panel is touched, the X and Y coordinate values of the
touched point and the coordinate values of the specified point are dis-
played. The coordinate values set with SIM 65-1 are used as the refer-
ence.

Setting of soft switches other than SW1 can be changed and checked. 

1) Enter the soft switch number to be checked or changed with 10-

key.

The current set state is displayed.

Select 1, and 
press [START] key.

Select other than 1, and 
press [START] key. 

Press [START] key, or 
press [CUSTOM SETTINGS] key.

SIMULATION 64-1

SELF PRINT MODE. SELECT 0-7, AND PRESS START.

0. TRAY SELECT  :

1

   1. PRINT START

2. PRINT PATTERN:

87

  3. DENSITY   :

1

4. MULTI :       

1

   5. MODE      :

1

6. LEVEL :       

1

   7. DUPLEX    :

1

1

SIMULATION 64-1

SELF PRINT MODE. INPUT VALUE, AND PRESS START.

(PRINT PATTERN)

INPUT 1-98.

71

SIMULATION 64-1

SELF PRINT MODE. INPUT VALUE, AND PRESS START.

(DENSITY)

1-255

100

SIMULATION 64-1

SELF PRINT MODE. INPUT VALUE, AND PRESS START.

(MULTI COUNT)

1-999

1

SIMULATION 64-1

SELF PRINT MODE. SELECT 1-8, AND PRESS START.

(MODE)

1.STANDARD  2.SMOOTHING  3.TONER SAVE  4.HALF TONE

5.SMOOTHING+ TONER SAVE  6.SMOOTHING+ HALF TONE

7.TONER SAVE+ HALF TONE

8.SMOOTHING+ TONER SAVE+ HALF TONE

1

SIMULATION 64-1

SELF PRINT MODE. INPUT VALUE, AND PRESS START.

(LEVEL)

1-5

3

SIMULATION 64-1

SELF PRINT MODE. SELECT 1-5, AND PRESS START.

(FEED TRAY)

  1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4  5.BPT

1

SIMULATION 64-1

SELF PRINT MODE. SELECT 1-2, AND PRESS START.

(DUPLEX)

  1.NO 2.YES

1

SIMULATION 64-1

SELFT PRINT MODE.. EXECUTING···

0. TRAY SELECT  :

1

2. PRINT PATTERN:

87

  3. DENSITY   :

1

4. MULTI :       

1

   5. MODE      :

1

6. LEVEL :       

1

   7. DUPLEX    :

1

0

(3)

(2)

(4)

(5)

(6)

(0)

(7)

65-1

Adjustment

Used to adjust the touch panel (LCD display section) 
detection position.

Operation (Display/Operation key)

65-2

Adjustment/Setup/Operation data output/Check 
(Display/Print)

Used to check the result of the touch panel (LCD 
display) detection position adjustment. (The 
coordinates are displayed.)

Operation (Display/Operation key)

66-1

Setting

Used to change and check the FAX soft switch 
functions. (Used to change and check the functions 
provided for the FAX soft switches.)

FAX

SIMULATION 65-1

SIMULATION 65-2

400

500

600

40

100            200            300

100

140

600

180

200