Read Sharp AR-M550 (serv.man14) Service Manual online
AR-M550/M620 SETTING AND ADJUSTMENTS 7 - 35
8) Check the print density.
Repeat steps 6 to 8 until an acceptable print density is obtained.
Note: Adjusting the Fax print density through this simulation changes
the print density settings for all Fax modes to the density level
applied by carrying out this simulation.
The Fax mode print density settings for individual Fax modes
adjusted through Simulations 46-13, -14, -15, -16 and -45 are
changed to the print density level applied by this simulation.
applied by carrying out this simulation.
The Fax mode print density settings for individual Fax modes
adjusted through Simulations 46-13, -14, -15, -16 and -45 are
changed to the print density level applied by this simulation.
This adjustment is intended to the print mode for each Fax mode indi-
vidually. In manual mode, the print density setting for each print density
adjustment level (1 to 5) can be adjusted to a custom density level.
vidually. In manual mode, the print density setting for each print density
adjustment level (1 to 5) can be adjusted to a custom density level.
1) Set the test chart (UKOG-0162FCZZ) on the original table so that it
aligns with the front frame. Then put four or five pieces of A3 (11" x
17") paper .
17") paper .
2) Go through the simulation modes that correspond to the Fax
modes for which to adjust the print density (i.e., the modes speci-
fied in Simulations 46-13, -14, -15, -16, or -45).
fied in Simulations 46-13, -14, -15, -16, or -45).
ADJ 10B
Adjust the fax mode print density in
standard mode
standard mode
ADJ 10C
Adjust the fax mode print density in
small-character mode
small-character mode
ADJ 10D
Adjust the fax mode print density in fine
mode
mode
ADJ 10E
Adjust the fax mode print density in
super fine mode
super fine mode
ADJ 10F
Adjust the fax mode print density in
600dpi mode
600dpi mode
00
Select 2, and
press [START] key.
press [START] key.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
Item
Set
range
Default
0
TRAY SELECT
Paper feed tray selection
1
PRINT START
Print start (Default)
2
EXP LEVEL
Exposure level selection
3
AUTO
Auto
0 - 99
50
4
1.0
Exposure level 1
5
2.0
Exposure level 2
6
3.0
Exposure level 3
7
4.0
Exposure level 4
8
5.0
Exposure level 5
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS
START.
0.TRAY SELECT
1
1.PRINT START
2.EXP LEVEL
1
3.AUTO
50
4.1.0
50
5.2.0
50
6.3.0
50
7.4.0
50
8.5.0
50
50
1
1
Select 1,
and press
[START] key.
and press
[START] key.
Select 0, and press [START] key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL),INPUT VALUE 0-99, AND
PRESS START.
4.1.0
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). NOW PRINTING.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-6, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE +20:DSPF MODE)
Select other than 0 - 2,
and press [START] key. Press [CUSTOM SETTINGS] key.
and press [START] key. Press [CUSTOM SETTINGS] key.
Press [START] key.
Press [CUSTOM SETTINGS] key,
or terminate copying.
or terminate copying.
Press [START] key, or
press [CUSTOM SETTINGS] key.
press [CUSTOM SETTINGS] key.
1
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0 5.2.0
6.3.0 7.4.0 8.5.0
Click on the first or last page to see other AR-M550 (serv.man14) service manuals if exist.