AR-M351U, AR-M451U (serv.man16). Adjustments - Sharp Copying Equipment Service Manual (repair manual). Page 15

AR-M351U/M451U, AR-M355U/M455U  ADJUSTMENTS  8 - 15

(Fax mode density)

The print density settings should be normally left at defaults but
should be adjusted according to user requests, if any.

1) Set the test chart (UKOG-0162FCZZ) on the original table so

that it aligns with the front frame. Then put four or five pieces
of A3 (11" x 17") paper . 

2) Go through the modes specified in Simulation 46-12.

3) Select the adjustment item (FAX EXP. LEVEL) using the

numeric keypad. 

4) Press the Start key. 

5) Press the Start key (A copy is created.)

Check the print density. 

If the print density is not at an acceptable level, do the follow-
ing steps.

6) Enter the print adjustment value using the numeric keypad.

7) Press the P or Start key

This applies the adjustment value. 

Pressing the Start key starts print operation as well as apply-
ing the adjustment value. 

8) Check the print density. 

Repeat steps 6 to 8 until an acceptable print density is obtained.

Note: Adjusting the Fax print density through this simulation

changes the print density settings for all Fax modes to the
density level applied by carrying out this simulation.
The Fax mode print density settings for individual Fax
modes adjusted through Simulations 46-13, -14, -15, -16
and -45 are changed to the print density level applied by
this simulation.

Image mode

Simulation for 

adjustment

All-mode 

adjustment

Individual-

mode 

adjustment

Fax mode 
print density 
adjustment 
(standard 
mode)

Auto 
mode

Binary mode

46-12

46-13

Manual Binary mode

Fax mode 
print density 
adjustment 
(small-
character 
mode)

Auto 
mode

Binary mode

46-14

Half tone 
mode

Manual Binary mode

Half tone 
mode

 Fax mode 
print density 
adjustment 
(fine mode)

Auto 
mode

Binary mode

46-15

Half tone 
mode

Manual Binary mode

Half tone 
mode

Fax mode 
print density 
adjustment 
(super fine 
mode)

Auto 
mode

Binary mode

46-16

Half tone 
mode

Manual Binary mode

Half tone 
mode

Fax mode 
print density 
adjustment 
(600dpi 
mode)

Auto 
mode

Binary mode

46-45

Half tone 
mode

Manual Binary mode

Half tone 
mode

00

Select 0, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

Item

Set 

range

Default

0

TRAY SELECT

Paper feed tray selection

1

COPY START

Copy START (Default)

2

FAX EXP. LEVEL FAX mode print density

0 - 99

50

SIMULATION 46-12

EXP.LEVEL SETUP FAX(AUTO SET). SELECT 0-2, AND PRESS 

START.

0.TRAY SELECT 

1

 1.COPY START

2.FAX EXP.LEVEL 

50

Press [CUSTOM SETTINGS] key. 

SIMULATION 46-12

EXP.LEVEL SETUP FAX(AUTO SET), INPUT VALUE 0-99, AND

PRESS START.

2.FAX EXP.LEVEL

50

1

Press [START] key.

Press [CUSTOM SETTINGS] key, 
or terminate copying.

SIMULATION 46-12

EXP.LEVEL SETUP FAX(AUTO SET). NOW PRINTING.

Select 1, and 
press [START] key.

Select other than 0 - 1, and 
press [START] key. 

SIMULATION 46-12

EXP.LEVEL SETUP FAX(AUTO SET).SELECT 1-5, AND PRESS

START.

(FEED TRAY)

 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

 5.BPT