Read Sharp AR-M351U / AR-M451U (serv.man16) Service Manual online
AR-M351U/M451U, AR-M355U/M455U ADJUSTMENTS 8 - 12
4) Loosen the fixing screw of the front or the rear frame mirror
base drive pulley.
5) Tighten the fixing screw of the mirror base drive pulley.
6) Perform procedures 1) through 3).
7) If La is not equal to Lb, perform procedures 4) and 5).
If La = Lb, the adjustment is completed.
Repeat procedures 1) through 6) until La = Lb.
Repeat procedures 1) through 6) until La = Lb.
E. Height adjustment of original detection light
emitting unit
1) Execute SIM 41-3.
2) Open the original cover. Press the original detection light-emit-
ting unit gradually with your finger to check the height at which
OCSW display on the LCD is highlighted.
OCSW display on the LCD is highlighted.
3) Open the original detection light-emitting unit gradually to
check the height at which OCSW display turns to the normal
state.
state.
4) If the heights are out of the specified range in procedures 2)
and 3), adjust the height of the original detection light emitting
unit by shifting the adjustment screw.
unit by shifting the adjustment screw.
5) After completion of adjustment, press the original detection
light emitting unit fully downward with your finger and release
it. Check that the original detection light-emitting unit moves
up smoothly.
it. Check that the original detection light-emitting unit moves
up smoothly.
<Specification>
F. Original size detection photo sensor check
1) Execute SIM 41-1.
2) Put A3 (or WLT) paper on the table glass, and check that all
the sensor displays (except for OCSW) on the LCD are high-
lighted.
lighted.
3) Gradually move the unit to the left, and check that the high-
lighted sensor displays turn off one by one sequentially.
G. Original size detection photo sensor
adjustment
1) Execute SIM 41-2.
∗
At that time, check that the scanner mirror base is at the
home position.
home position.
2) Open the document cover. Select 1 without placing paper on
the table glass, and press START.
3) When COMPLETE is displayed on the LCD, press CUSTOM
SETTING to return to the initial screen.
4) Place A3 (or WLT) paper on the table glass, select 2 and
press START.
When COMPLETE is displayed, the adjustment is normally
completed.
When COMPLETE is displayed, the adjustment is normally
completed.
∗
If ERROR is displayed, the error PD sensor is displayed.
<Specification>
•If La < Lb, turn the rear frame mirror base drive pulley in
direction B.
(Do not move the mirror base drive pulley shaft.)
(Do not move the mirror base drive pulley shaft.)
•If La > Lb, turn the rear frame mirror base drive pulley in
direction A.
(Do not move the mirror base drive pulley shaft.)
(Do not move the mirror base drive pulley shaft.)
A
B
Front side
Rear side
Adjust screw
32±0.5mm
SIMULATION 41-3
PD SENSOR DATA DISPLAY.
OCSW
PD1[128]: 200 PD2[128]: 200
PD3[128]: 50 PD4[128]: 52
PD5[128]: 51 PD6[128]: 50
PD7[128]: 52
Specification Adjustment position
Original size
detection position
detection position
32±0.5mm
Height adjustment
screw
screw
SIM 41-3
Select 2 and press [START] key.
(Error)
(Error)
Press [CUSTOM SETTINGS]
key.
key.
Specification
Adjustment
Document size detection photo
sensor adjustment
sensor adjustment
COMPLETE
SIM 41-2
SIMULATION 41-1
PD SENSOR CHECK..
OCSW
PD1
PD2
PD3
PD4 PD5 PD6 PD7
SIMULATION 41-2
PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START.
(PLEASE OPEN THE ORIGINAL COVER.)
1. NO ORIGINAL
2. A3 ORIGINAL
1
SIMULATION 41-2
Press [CUSTOM SETTINGS] key.
Select 1 and
press [START] key.
press [START] key.
PD SENSOR ADJUSTMENT.
NO ORIGINAL ··· COMPLETE (or "ERROR at
PD1 PD2
...")
A3 ORIGINAL ··· INCOMPLETE
SIMULATION 41-2
PD SENSOR ADJUSTMENT.
NO ORIGINAL ··· COMPLETE
A3 ORIGINAL ··· COMPLETE (or "ERROR at
PD1 PD2
...")
Click on the first or last page to see other AR-M351U / AR-M451U (serv.man16) service manuals if exist.