Read Sharp AR-M300 (serv.man11) User Guide / Operation Manual online
6-14
KEY OPERATOR PROGRAMS
■ Initialize/store settings
{Initialize and/or store settings}
The configuration settings (page 3-2) and the system
settings of the key operator programs (page 6-11)
can be stored in memory and can be recalled from
memory if the settings are changed. These can also
be reset to the factory default settings.
settings of the key operator programs (page 6-11)
can be stored in memory and can be recalled from
memory if the settings are changed. These can also
be reset to the factory default settings.
Restore factory defaults
This program is used to reset configuration settings
(page 3-2), default settings and interface settings of
the key operator programs (pages 6-11 and 6-12)
to the factory default settings. If you wish to record
the settings before resetting them, use “List Print”
of custom settings (page 3-8) to print the settings
before using this program.
(page 3-2), default settings and interface settings of
the key operator programs (pages 6-11 and 6-12)
to the factory default settings. If you wish to record
the settings before resetting them, use “List Print”
of custom settings (page 3-8) to print the settings
before using this program.
{Restore factory defaults}
Same as for the main unit.
NOTE
After this program is set, exit the key operator
program, turn off the main switch, and then turn on
the main switch again after at least 3 seconds. The
program will be effective at this time.
program, turn off the main switch, and then turn on
the main switch again after at least 3 seconds. The
program will be effective at this time.
Store current configuration
Use this program to store the current configuration
settings (page 3-2), default settings and interface
settings of the key operator programs (pages 6-11
and 6-12) in the printer’s nonvolatile memory. To
recall the stored settings, use the program “Restore
configuration” below.
settings (page 3-2), default settings and interface
settings of the key operator programs (pages 6-11
and 6-12) in the printer’s nonvolatile memory. To
recall the stored settings, use the program “Restore
configuration” below.
{Store current configuration}
Same as for the main unit.
Restore configuration
Use this program to recall the configuration settings
that have been stored in the printer's nonvolatile
memory by the program "Store current configuration"
above.
that have been stored in the printer's nonvolatile
memory by the program "Store current configuration"
above.
{Restore configuration}
Same as for the main unit.
NOTE
If the settings of “Enable TCP/IP”, “Enable NetWare”,
“Enable EtherTalk” or “Enable NetBEUI” has been
changed, exit the key operator program, turn off the
main switch, and then turn on the main switch again
after at least 3 seconds. The changes will become
effective at this time.
“Enable EtherTalk” or “Enable NetBEUI” has been
changed, exit the key operator program, turn off the
main switch, and then turn on the main switch again
after at least 3 seconds. The changes will become
effective at this time.
■ Product key
Use these programs to input data required to activate
the following systems.
the following systems.
PS3 expansion kit
This program must be used to activate a
PostScript expansion kits. For the password to
be entered, contact your dealer.
PostScript expansion kits. For the password to
be entered, contact your dealer.
{PS3 expansion kit}
Same as for the main unit.
{Network scanner expansion kit}
This program must be used to activate a network
scanner expansion kit. For the password to be
entered, contact your dealer. This program can
be used only if the machine is equipped with a
scanner module.
scanner expansion kit. For the password to be
entered, contact your dealer. This program can
be used only if the machine is equipped with a
scanner module.
E-mail alert and status
This program cannot be used now. This program
is reserved for future customer support through
a network.
is reserved for future customer support through
a network.
{E-mail alert and status}
Same as for the main unit.
{Printer expansion kit}
This program is used to activate the printer
expansion kit when using the unit as a network
printer. For the password to be entered, contact
your dealer.
expansion kit when using the unit as a network
printer. For the password to be entered, contact
your dealer.
Click on the first or last page to see other AR-M300 (serv.man11) service manuals if exist.