Read Sharp AR-FX4 (serv.man3) User Guide / Operation Manual online
PRINTING LISTS
121
Pr
in
in
ting
Lis
ts
5
The information shown in the "TYPE/NOTE" column of the report is as follows.
Sending Result
Explanation
OK
Transmission was completed successfully.
BUSY
Transmission was not successful because the line was busy.
CANCEL
A transmission was cancelled while in progress.
P. FAIL
The power was turned off or a power failure occurred.
NO RX POLL
When your machine was polled,
(1) The polling machine did not have its own fax number programmed.
(1) The polling machine did not have its own fax number programmed.
PASSCODE # E
When your machine was polled,
(1) The other machine's system number did not match any of your machine's
(1) The other machine's system number did not match any of your machine's
ID numbers.
(2) Your machine's system number did not match the other machine's
system number.
(3) The other machine's fax number had not been stored as a polling
passcode in your machine.
RX TERM FAIL
When confidential transmission was attempted,
(1) The receiving machine did not have a confidential function, or it was not
(1) The receiving machine did not have a confidential function, or it was not
a Sharp machine.
(2) The receiving machine only had one confidential box and an ID code
(confidential ID code) had not been programmed.
CONF TX CNCL
When a relay request transmission was attempted,
(1) The other machine did not have a relay broadcast function.
(2) The other machine was not a Sharp machine.
(1) The other machine did not have a relay broadcast function.
(2) The other machine was not a Sharp machine.
NO REL FUNC
When a confidential transmission was attempted,
(1) There was a mistake in the confidential box number setting, or the box
(1) There was a mistake in the confidential box number setting, or the box
number was not programmed in the other machine.
(2) Your fax number was not programmed in your machine.
REL REQ FAIL
When you attempted a relay request transmission,
(1) Your fax number was not programmed in your machine.
(2) You specified an auto dial number that was not stored in the other machine.
(3) Your fax number was not stored as a relay ID code in the other machine.
(1) Your fax number was not programmed in your machine.
(2) You specified an auto dial number that was not stored in the other machine.
(3) Your fax number was not stored as a relay ID code in the other machine.
ORIG ERROR
When you attempted to send a fax from the SPF in direct transmission mode,
a missfeed occurred.
a missfeed occurred.
ERRORxx xxxx
Line conditions prevented the transmission from taking place normally.
First 2 digits of line error code: Error code from 00 to 31
Last 4 digits of line error code: Code for use by service technicians.
First 2 digits of line error code: Error code from 00 to 31
Last 4 digits of line error code: Code for use by service technicians.
xxx-xxx OK
When group dialling, broadcast transmission, relay request transmission, or
F-code relay request transmission was performed,
xxx- : Indicates total number of transmissions.
xxx OK : Indicates completed transmissions.
F-code relay request transmission was performed,
xxx- : Indicates total number of transmissions.
xxx OK : Indicates completed transmissions.
NO S ADD FUNC
When an F-code transmission was attempted,
(1) The other machine did not have an F-code function.
(2) An F-code was not programmed in the other machine.
(1) The other machine did not have an F-code function.
(2) An F-code was not programmed in the other machine.
S ADD TX FAIL
When an F-code transmission was attempted,
(1) The sub-addresses did not match.
(2) The passcodes did not match.
(3) F-code memory polling settings were established.
(1) The sub-addresses did not match.
(2) The passcodes did not match.
(3) F-code memory polling settings were established.
SA POLL ERR
When F-code memory polling was attempted,
(1) The F-code memory polling box specified by the sub-address did not exist.
(2) The sub-address specified a box other than the F-code memory polling box.
(1) The F-code memory polling box specified by the sub-address did not exist.
(2) The sub-address specified a box other than the F-code memory polling box.
PASSCODE# ERR
When F-code memory polling was attempted,
(1) The passcodes did not match.
(1) The passcodes did not match.
NGRCTFAUWMDQQMࡍࠫ㧞㧜㧜㧝ᐕ㧤㧝㧜ᣣޓ㊄ᦐᣣޓඦᓟ㧞ᤨ㧠㧢ಽ
Click on the first or last page to see other AR-FX4 (serv.man3) service manuals if exist.