AR-FX2 (serv.man2). AR-FX2-Service Manual - Sharp Copying Equipment Service Manual (repair manual). Page 52

<Card information>
The following information of the inserted card is displayed.

• Card information

a. Kind of the card
b. Version of the card
c. DownLoad Program Version No. or registered data Program

Version No.

d. Write end

• Data information

a. Model name
b. Main Program Version No. or registered data ID No.
c. Write end

∗ As the card kind, either of DownLoad, Registration, and Unknown

is displayed.

∗ As write end, Erased or Written is displayed.

(3) Slot selection

If there are two slots available, no slot is selected immediately after
starting this application program.
Select the slot to be used. Click SlotSelect(S) in the menu and
specify either Slot1 or Slot2. If the card is inserted into the
specified slot, the card kind is displayed in the main menu.

∗ If only one slot is available in the use environment, the slot is

automatically selected and there is no need to select the slot.
(SlotSelect(S) is not displayed in the menu.)

(4) Device Selection

If a slot is selected and the Slot section in the main menu is turned
to green, the card is recognized by the application program. (If the
Slot section keeps yellow or gray (system color), there are some
troubles in the card and it cannot be used.)
If, however, the Device section is gray (system color), the inserted
card is not recognized as a specified one (Intel_28F008_5V) or the
device information of the card is destroyed by some reason.
To use such a card, the card device must be manually specified.
Specify Card(C)_SetDevice(V)_Intel_28F008_5V in the menu.

When the device is specified, the Device section turns yellow to
allow access to the card.
∗ Though access to the cars is allowed by specifying the device, if

the specified device differs from the actual device, an unexpected
error may occur.

(5) Selection of card type

When access to the cars is allowed and the card’s format type in-
formation is recorded in the specified address of the inserted card,
the operation mode of the application is automatically specified.
If, however, there is no format type information in the card, data
must be written into ProgramArea (0 

∼ 1fffffH) or the format type

must be specified manually.
For writing data, refer to the descriptions below.
To specify the format type manually, specify the items following
Card(C)_SetCardType(T) in the menu.

The current operation mode of the application is displayed in the
CardType section.
The File(F) menu which can be operated differs depending on the
operaton mode of the application.
The CardType is changed when the ProgramArea is erased or data
are written into it.

(6) Erase, erase check

If access to the card is allowed (Slot, green; Device, green or yel-
low),  EraseArea(E) and EraseCheck(C) in File(F) menu can be
used.
EraseArea erases all data in the specified are of the card. (They
are filled with FFH actually.)
EraseCheck checks that erase operation is executed normally or
not.
There are three modes for area specification respectively.

ProgramArea

Address 0 

∼ 1fffffH of the card

DataArea

Address 200000 

∼ 3fffffH of the card.

AllArea

All area of the card

EraseArea has an option of EraseCheckOption.
If this option is checked, erase check is automatically performed
after erasing.

(7) Write data into ProgramArea from the file.

Motoroller S37 file data are written into ProgramArea of the card.
Click Option(O)_WriteProgramArea(P) in the menu.

After the confirmation message, the common dialog box is dis-
played. Specify S37 file to be written.

1) When writing a download program (This procedure must be per-

formed when a program is newly downloaded.)

<a> Click [Option] – [Write Program Area].
<b> Select the version-up file [DwldXXX.s37].
<c> Writing is ended. 

2) When writing the main program

<a> Click [FILE] – [Write Main Program].
<b> Select the version-up file [CromXXX.s37].
<c> Writing is ended.

When the file is specified, the progress bar is displayed to indicate
the progress level and writing is processed.
The flow of processes is as follows.
ProgramArea erase 

→ Erase check → Data read and write → verify

check of written data
∗ To interrupt the process, press the ESC key.

After completion of data write, initialize the main menu again. (The
data are read from the card.)

(8) Process menu for each card type

The process menu differs depending on the card format type as
follows:

<DownLoadCard>

In the case of DownLoadCard,  WirteMainProgram(M) in the File(F)
menu can be used.  This menu is used to write MainProgram into
DataArea of DownLoadCard.  The writing procedures are the same
as those of WriteProgramArea in the Option menu previously
stated.

AR-FX2

9  –  2