Read Sharp AR-FN2 (serv.man5) Service Manual online
[6] TEST MODE AND SETTING DIP
SWITCHES
1. Position of dip switches
The dip switches are located on the main PWB as shown in the figure
below.
below.
2. Setting dip switches
(1) Selecting test modes
Select the test mode type using the dip switches. Holding down the
push switch, turn on the power to get in the selected test mode. After
that, change over the dip switches and press the push switch as
necessary.
push switch, turn on the power to get in the selected test mode. After
that, change over the dip switches and press the push switch as
necessary.
1
Load individual operation check mode 1
2
Load individual operation check mode 2
3
Staple operation check mode
4
Alignment plate stop position check mode
5
Non-job tray exit mode
6
No-reverse offset exit mode
7
Reverse offset exit mode
8
Staple exit mode
9
Reverse offset aging mode
10
Staple aging mode
(2) Setting test mode
1 2 3 4
Description
1
Loaded test mode 1
In this test mode, each actuator is
activated and deactivated every
time the push switch is pressed.
The following operations is
repeated:
Reverse
In this test mode, each actuator is
activated and deactivated every
time the push switch is pressed.
The following operations is
repeated:
Reverse
SOL
¯
Puddle
SOL
¯
Discharge
SOL
¯
Transfer motor
¯
Stack tray motor
1 2 3 4
Description
2
Loaded test mode 2
In this mode, each actuator is
activated and deactivated every
time the push switch is pressed.
The following operations are
repeated:
Reverse motor
(forward rotation)
In this mode, each actuator is
activated and deactivated every
time the push switch is pressed.
The following operations are
repeated:
Reverse motor
(forward rotation)
¯
Reverse motor
(reverse rotation)
Matching plate
(reverse rotation)
Matching plate
3
Stapler operation check mode
In this mode, the stapler operates
once every time the push switch is
pressed.
In this mode, the stapler operates
once every time the push switch is
pressed.
4
Matching plate stop position
check mode
In this mode, the matching plate
stops at the paper matching
position and returns to its home
position every time the push
switch is pressed.
Staple discharge JOG discharge
A4
check mode
In this mode, the matching plate
stops at the paper matching
position and returns to its home
position every time the push
switch is pressed.
Staple discharge JOG discharge
A4
®
Letter
®
B5
®
A4
®
Letter
®
B5
5
Non-job tray discharge mode
After turning on the machine in a
test mode, set to this mode with
the dip switches. Pressing the
push switch sets paper size and
performs initial operation. After
the completion of the initial
operation, it becomes possible to
pass paper. The settings of the
dip switches are as follows:
After turning on the machine in a
test mode, set to this mode with
the dip switches. Pressing the
push switch sets paper size and
performs initial operation. After
the completion of the initial
operation, it becomes possible to
pass paper. The settings of the
dip switches are as follows:
6
No-reversion offset discharge
mode
After turning on the machine in a
test mode, set to this mode with
the dip switches. Pressing the
push switch sets paper size and
the number of sheets to be
processed and performs initial
operation. After the completion of
the initial operation, it becomes
possible to pass paper. The
settings of the dip switches are as
follows:
mode
After turning on the machine in a
test mode, set to this mode with
the dip switches. Pressing the
push switch sets paper size and
the number of sheets to be
processed and performs initial
operation. After the completion of
the initial operation, it becomes
possible to pass paper. The
settings of the dip switches are as
follows:
LED
DIPSW
ROM
CPU
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
1
ON
OFF
OFF
A3_T
2 3 4
A4_Y
A4_T
1
ON
OFF
OFF
LETTER_Y
2 3 4
LETTER_T
EXE_Y
ON
OFF
OFF
1 2
ON
OFF
OFF
A4
LETTER
B4
EXE
3 4
ON
OFF
OFF
2pls
5pls
10pls
30pls
6 – 1
Click on the first or last page to see other AR-FN2 (serv.man5) service manuals if exist.