Read Sharp AR-F151 (serv.man11) Service Manual online
SW
No.
No.
Bit
No.
ITEM
Soft SW setting and function
Factory Setting
21
3
Picture quality priority selection
Used to set the default resolution in sending.
0
4
Reserved
0
5
6
7
8
6
7
8
Number of reception start calls
Used to set the number of calls before reception in the auto
reception mode. The set range is 0 to 9 times.
reception mode. The set range is 0 to 9 times.
Number = 8
× Bit5 + 4 × Bit6 + 2 × Bit7 + 1 × Bit8 rings
Set range : 0 –9
0
0
1
0
0
1
0
22
1
2
3
4
2
3
4
Number of auto reception select
Used to set the number of calls before reception in the
manual reception mode. This setup is used as a backup
function when the external telephone does not respond. The
set range is OFF and 1 to 9 times.
manual reception mode. This setup is used as a backup
function when the external telephone does not respond. The
set range is OFF and 1 to 9 times.
Number = 8
× Bit1 + 4 × Bit2 + 2 × Bit3 + 1 × Bit4 rings
Set range : 0(= OFF), 1 –9
0
0
0
0
0
0
0
5
Reserved
0
6
7
8
7
8
Result list print
Used to set the printing conditions of the result list after
completion of communication.
completion of communication.
0
0
1
0
1
23
1
2
3
4
2
3
4
Number of recall times
Used to set the number of times of recalls when sending is
not normally completed due to busy status of the other party
or a communication error.
The set range is OFF and 1 to 14 times. For some causes
of the communication error, however, the number of times of
recalls must be set to a smaller level.
not normally completed due to busy status of the other party
or a communication error.
The set range is OFF and 1 to 14 times. For some causes
of the communication error, however, the number of times of
recalls must be set to a smaller level.
Recall Times = 8
× Bit1 + 4 × Bit2 + 2 × Bit3 + 1 × Bit4
times
Set range : 0(= OFF), 1 –14
Set range : 0(= OFF), 1 –14
0
0
1
0
0
1
0
5
6
7
8
6
7
8
Recall interval
Used to set the recall interval when a transmission is not
normally completed due to busy status of the other party or
a communication error.
The set range is 1 to 15 minutes.
normally completed due to busy status of the other party or
a communication error.
The set range is 1 to 15 minutes.
Recall Interval = 8
× Bit5 + 4 × Bit6 + 2 × Bit7 + 1 × Bit8
min
Set range : 1 –15
Set range : 1 –15
0
1
0
1
1
0
1
24
1
2
3
4
2
3
4
Remote select number
Used to select the first digit of the select request signal
when selecting from the external telephone to FAX reception.
The set range is 0 to 9.
when selecting from the external telephone to FAX reception.
The set range is 0 to 9.
Number = 8
× Bit1 + 4 × Bit2 + 2 × Bit3 + 1 × Bit4
Set range : 0 – 9
0
1
0
1
1
0
1
5
Remote reception
Used to set whether “Remote select number” + “
∗∗” from an
external telephone is detected and switched to FAX
reception or not.
reception or not.
1
6
FAX signal reception
Used to set whether CNG signal is detected during OFF-
HOOK and switched to FAX reception or not.
HOOK and switched to FAX reception or not.
1
7
Auto cover paper
Used to set whether a cover is attached to the last page in
every transmission or not.
every transmission or not.
0
8
Reserved
0
1 : Fine
0 : Standard
Bit No.
Always
Err/Tim
Send
Never
Error
6
0
0
0
0
1
7
0
0
1
1
0
8
0
1
0
1
0
1 : ON
0 : OFF
1 : ON
0 : OFF
1 : ON
0 : OFF
AR-F151
9 – 26
Click on the first or last page to see other AR-F151 (serv.man11) service manuals if exist.