Read Sharp AR-C330 (serv.man5) Service Manual online
AR-C330 SETTING AND ADJUSTMENTS 7 - 30
The print density should vary gradually from the lower density to
the higher density without reversion of changing direction.
the higher density without reversion of changing direction.
The density level of each color should be almost the same.
It is acceptable for patch B not to be copied.
Patch A is not copied.
When, however, the color balance is adjusted according to the
user's request, there is no need to adjust to the standard color bal-
ance as stated above.
user's request, there is no need to adjust to the standard color bal-
ance as stated above.
5) Select the color to be adjusted and select the adjustment point
with the scroll key.
6) Enter the adjustment value with the 10-key and press the OK
key.
The adjustment value can be selected in the range of 245 –
755 (1 – 999). When SIM 46-24 is used to perform the auto-
matic color balance and the density adjustment, all the set val-
ues of this simulation are set to 500.
755 (1 – 999). When SIM 46-24 is used to perform the auto-
matic color balance and the density adjustment, all the set val-
ues of this simulation are set to 500.
To increase the density, increase the adjustment value. To
decrease the density, decease the adjustment value.
decrease the density, decease the adjustment value.
Repeat procedures 3) – 6) until the condition of procedure 4) is
satisfied.
satisfied.
When the overall density is low or patch A is copied with a high
density, use the arrow keys to change all the adjustment values of
A – O simultaneously and uniformly.
density, use the arrow keys to change all the adjustment values of
A – O simultaneously and uniformly.
Then perform the patch density adjustment. This allows to make
an efficient adjustment.
an efficient adjustment.
By using the black patch as the reference, adjust so that the color
balance of the black patch of each process (CMY) in A – O
becomes virtually same as the black patch.
balance of the black patch of each process (CMY) in A – O
becomes virtually same as the black patch.
In this simulation mode, press CLEAR key to return to the normal
copy mode and make actual copies of the service chart and user
documents. Check the adjustment result.
copy mode and make actual copies of the service chart and user
documents. Check the adjustment result.
7) Execute SIM 44-21.
The initial setup of half tone image correction is performed.
This procedure is to store the copy color balance adjustment data
as the reference data for half-tone correction.
as the reference data for half-tone correction.
This procedure should be always executed immediately after com-
pletion of ADJ M17/ADJ 3 (Color balance adjustment (Manual))
with SIM 46-21.
pletion of ADJ M17/ADJ 3 (Color balance adjustment (Manual))
with SIM 46-21.
When ADJ M17/ADJ2 (Color balance adjustment (Auto)) is per-
formed with SIM 46-24, this procedure is automatically performed.
formed with SIM 46-24, this procedure is automatically performed.
When EXECUTE key is pressed, it is highlighted and the opera-
tion is started.
tion is started.
It takes several minutes to complete the operation. When the
operation is completed, the screen returns to the original state.
After completion of the operation, cancel the simulation.
operation is completed, the screen returns to the original state.
After completion of the operation, cancel the simulation.
8) Execute the half tone image correction. (Forcible execution)
(SIM 44-26)
When EXECUTE key is pressed, it is highlighted and the opera-
tion is started. It takes several minutes to complete the operation.
When the operation is completed, the screen returns to the origi-
nal state.
tion is started. It takes several minutes to complete the operation.
When the operation is completed, the screen returns to the origi-
nal state.
After completion of the operation, cancel the simulation.
9) Use the test chart UKOG-0283FCZZ and check the copy color
balance and the density in the Text/Printed photo mode.
(Refer to the section of the copy color balance and the density
check.)
(Refer to the section of the copy color balance and the density
check.)
If the copy color balance and the density are not in the specified
level, repeat procedures 7) through 9) until they are in the speci-
fied level.
level, repeat procedures 7) through 9) until they are in the speci-
fied level.
However, repetition is limited to three times. If repetition of the
above procedures does not set the copy color balance and the
density to the specified level, there may be some other reason.
Investigate the reason and repair or fix the problem, then perform
all the procedures of print quality adjustment from the beginning.
above procedures does not set the copy color balance and the
density to the specified level, there may be some other reason.
Investigate the reason and repair or fix the problem, then perform
all the procedures of print quality adjustment from the beginning.
10) When the color balance is customized, register the color bal-
ance as the service target by SIM 63-7.
When the color balance is not customized, there is no need to
perform this work.
perform this work.
If the customized color balance is registered as the service tar-
get, when the color balance is adjusted in the next time, the
automatic color balance adjustment mode can be used. In the
next color balance adjustment, select the service target color
balance in the automatic color balance adjustment mode, and
the color balance will be adjusted to the same color balance
as registered this time.
get, when the color balance is adjusted in the next time, the
automatic color balance adjustment mode can be used. In the
next color balance adjustment, select the service target color
balance in the automatic color balance adjustment mode, and
the color balance will be adjusted to the same color balance
as registered this time.
Click on the first or last page to see other AR-C330 (serv.man5) service manuals if exist.