AR-407 (serv.man4). AR287 337 407 507-Service Manual - Sharp Copying Equipment Service Manual (repair manual). Page 19

 4:

AXIS controller

  8:

Tandem connection (Initiator)

10:

Tandem connection (Target)

20:

Network scanner controller (NS1)

Either of the above values is set.

*

AR-287 is not provided with the tandem setting. 
However, the display is not changed. When tandem setup is tried, it
is rejected.

Purpose

Setting

Function
(Purpose)

Used to set whether white paper discharge count up is
performed or not.
("White paper" means insertion paper in the OHP inser-
tion paper mode (without copy), cover paper in the
cover paper insertion mode (without copy)/back cover,
and white paper in the duplex exit mode (CA etc.).)

Item

Operation

Operation/
Procedure

When this simulation is executed, the current set value
is displayed.

Under this state, the set value can be changed with the 10-key.
When the OK key is pressed, the currently set value is stored in the
EEPROM.

Set value

Content

A

0

White paper count up is not performed.

1

White paper count up is performed.

Destination

Default

Japan/Australia

0 (Count up is not performed.)

Others

1 (Count up is performed.)

When set to 0 (count up is nor performed), the following counters do
not count up.

·

COPIES counter

·

Total counter

·

Maintenance counter

·

Developer counter

·

Department management counter

·

The signal (PNC) for the external auditor (mechanism counter) is
not outputted.

Purpose

Adjustment

Function
(Purpose)

Used to adjust the copy image position and the void
area (image loss) on the print paper in the copy mode.
(The same adjustment can be made with SIM 50-2
(simple method).)

Item

Picture quality

Image position

Operation/
Procedure

1. Select the adjustment item with [

­

], [

¯

] keys.

2. Enter the adjustment value with the 10-key.

3. Press the [OK] key. (The adjustment value entered in procedure 2

is set.)

A. Document scan start position adjustment value (RRC-A)

Used to adjust the timing of outputting the image lead edge signal
(SCAN signal) after starting document scanning. (0 – 99: Refer-
ence value 50)

B. Resist roller clutch OFF timing adjustment value (RRC-B)

Used to adjust the timing of turning ON the resist roller after recep-
tion of the resist signal (LD_START). (0 – 99: Reference value 50)

C. Rear edge void quantity adjustment value (DEN-B)

Used to set the void quantity on the rear edge. (0- 99: Reference
value 30)

D. Image loss quantity set value (IMAGE LOSS)

Used to set the image loss quantity. (0 – 99: reference value 20)

E. Lead edge void quantity set value (DEN-A)

Used to set the void quantity on the document lead edge. (0 – 99:
Reference value 20)

1. Set the image loss quantity (IMAGE LOSS) and the paper lead

edge void quantity (DEN-A) to desired values. (0 – 99:
0.1mm/step)

2. Adjust the document scan start position (RRC_A) so that the im-

age loss quantity of an actual copy image becomes the set value
of procedure 1. (0 – 99: 0.29mm/step)

3. Adjust the resist roller clutch ON timing (RRC_B) so that the lead

edge void quantity of an actual copy image becomes the set value
of procedure 1. (0 – 99: 0.24mm/step)

4. Adjust the rear edge void quantity (DEN_B). (0 – 99: 0.1mm/step)

Purpose

Adjustment

Function
(Purpose)

Used to adjust the copy image position and the void
area (image loss) on the print paper in the copy mode.

(Simple adjustment)
(This simulation allows the same simulation with SIM
50-1 more simply. )

Item

Picture quality

Image position

Operation/
Procedure

1. Select the adjustment item with [

­

], [

¯

] keys.

2. Enter the adjustment value with the 10-key.

3. Press the [OK] key. (The value entered in procedure 2 is set.)

Used to adjust the lead edge by entering the lead edge shift on each
lead edge of 400% copy.

AR-287/337

AR-407/507

7 – 55

4/5/2000