Read Sharp AR-275 (serv.man10) Service Manual online
AR-235/275 SIMULATION - 8
Note: Executable only when the finisher is installed.
Operation/procedure (Pattern 12)
[Selection 1]
Select with the 10-key.
[Selection 2]
(Input/Selection screen)
Operation/procedure
The operating states of the sensor and the detector are displayed.
The active sensors and detectors are highlighted.
Note: Execution is possible only when the option cassette is installed.
Operation/procedure (Pattern 9)
Select the load to check with the 10-key.
During execution of load operation, [EXEC] is highlighted.
Pressing the [BACK] key under this state interrupts the operation.
During execution of load operation, [EXEC] is highlighted.
Pressing the [BACK] key under this state interrupts the operation.
Display items
Content
Installation
range
Default
1:PAPER PUSH TMG
Paper holder
descending timing in
non-staple
descending timing in
non-staple
34-66
50
Used to adjust the descending timing of the
paper holder lever before lift-up operation
after paper exit or offset operation. (The
paper holder lever prevents against paper
shift in paper top surface detection and paper
stacking .)
paper holder lever before lift-up operation
after paper exit or offset operation. (The
paper holder lever prevents against paper
shift in paper top surface detection and paper
stacking .)
2:PAPER OUT DOWN
Tray descending
distance after non-
staple paper exit
distance after non-
staple paper exit
0-12
1
Used to adjust the offset tray descending
distance after non-staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
distance after non-staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
3:STAPLE UP
Tray lift distance
before staple paper
exit
before staple paper
exit
0-12
6
The height of the tray standby position in
stapling is changed for that in non-stapling to
improve stacking capacity in stapling. (The
relative distance for the height of the tray
standby position in non-stapling is set.)
stapling is changed for that in non-stapling to
improve stacking capacity in stapling. (The
relative distance for the height of the tray
standby position in non-stapling is set.)
4:STAPLE DOWN
Tray descending
distance after staple
paper exit
distance after staple
paper exit
0-12
6
Used to adjust the offset tray descending
distance after staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
distance after staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
5:OFFSET INI.POS
Offset tray shift
position adjustment
position adjustment
0-99
13
Used to shift the offset tray to the shipment
position or the disassembly position.
The offset tray is shifted to the specified
counter position.
position or the disassembly position.
The offset tray is shifted to the specified
counter position.
(In the case of 0 - 94 (Shipment position: 13))
1) Initialize the offset tray normally.
2) The tray descends to the parameter posi-
tion + 1 pulse position.
3) The tray lifts up to the specified parame-
ter position.
(Disassembly position: 94 - 99)
1) The tray descends to the bottom.
* If there is some paper in the offset tray, the
tray cannot descend to the specified posi-
tion. Check to insure that there is no paper
in the tray before execution.
tion. Check to insure that there is no paper
in the tray before execution.
3-11
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the shifter.
Item
Operation
(Initial screen)
(Executing screen)
1:F-R
Reciprocating operation
2:HP CHECK
Home position check
SFTHP:
Shifter home position (At detection, highlighted)
[
←
] key
Shifts the position toward R side by the specified steps.
[
→
] key
Shifts the position toward F side by the specified steps.
[
↑
] key
Shifts to the home position.
4
4-2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensor and detector in
the option tray and the related circuit.
the option tray and the related circuit.
Section
Paper feed
Item
Operation
PED2
2nd cassette paper empty sensor
LUD2
2nd cassette paper upper limit detection sensor
PFD2
2nd cassette paper pass sensor
CD2
2nd cassette empty sensor
PED3
3rd cassette paper empty sensor
LUD3
3rd cassette paper upper limit detection sensor
PFD3
3rd cassette paper pass sensor
CD3
3rd cassette empty sensor
PED4
4th cassette paper empty sensor
LUD4
4th cassette paper upper limit detection sensor
PFD4
4th cassette paper pass sensor
CD4
4th cassette empty sensor
DSWR3
3rd cassette right door detection sensor
DSWR2
2nd cassette right door detection sensor
DSWR4
4th cassette right door detection sensor
4-3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the load in the option
tray and the control circuit.
tray and the control circuit.
Section
Paper feed
Item
Operation
Sim3-11 SHIFTER CHK
1:F-R
2:HP CHECK
1
Sim3-11 SHIFTER CHK
1:
F-R
2:HP CHECK
EXEC 1
Sim3-11 SHIFTER CHK
SFTHP
[ ]:R [ ]:HP [ ]:F
Sim4-2 SENSOR CHECK
PED2 LUD2 PFD2
CD2
PED3 LUD3 PFD3 CD3
PED4
LUD4
PFD4 CD4
DSWR2 DSWR3 DSWR4
Click on the first or last page to see other AR-275 (serv.man10) service manuals if exist.