AR-155 (serv.man11). AR150 155 ARF151 Service Manual-Simulation Fax Software Switch Trouble Codes - Sharp Copying Equipment Service Manual (repair manual). Page 16

04

Signal send mode

This mode is used to send various signals to the line. The FAX signal is sent in
the level set with the soft switch.
There are the following kinds of signals:

04:SIGNAL SEND

10

Image memory
clear mode  (Only
the image data is
cleared.)

This mode is used to clear the image data memory (DRAM).

10:IMAGE MEM CLEAR

14

Dial test /
adjustment mode
(Pulse 10 pps)

This mode is used to dial in dial pulse (10PPS) and to set the pulse make ratio
adjustment value.
The range of make ratio variable range: -8% 

∼ +7%

The setup is reflected on the adjustment value area of the soft switch.
The dialed number is fixed to “1590.”

14:DIAL TEST 10 PPS

16

Dial  test    mode
(Tone)

This mode is used to dial with DTMF.
The number to be dialed is fixed to “123456789

∗0#”.

16:DIAL TEST TONE

21

Print out soft
switch mode

This mode is used to print the report on the current soft switch setup.

21:PRINT SOFT SW

42

FAX Panel check
mode

This mode is used to check the keys and the LED on the FAX panel.
When any key on the FAX panel other than the STOP key is pressed, the name
of the pressed key is displayed on the LCD.
The LED’s on the FAX panel are lighted one by one sequentially.
When any change is made on a sensor in the SPF section, the sensor name as
well as its ON/OFF status is displayed on the LCD.

42:FAX PANEL TEST

43

Signal detect mode

This mode is used to detect signals in the line, and the detected signal name is
displayed on the LCD. The signals to be detected are CNG, DTMF, and silent.
The detection conditions conform to the soft switch setup.

43:SIG. DETECT

44

Long distance
comm. Select mode

This mode is used to specify the other party FAX numbers registered in the one-
touch/speed dial,  with which communication errors occur frequently due to poor
line conditions
To the specified parties, the max. transmission speed is compulsorily reduced to
stabilize the communication line.
The speed is available in 9600BPS and 4800BPS.

44:LONG DIST COMM

(1) Soft SW change method

Procedure

LCD

Operation

1

Press FUNCTION, 9, 

∗, 8, #, 7.

DIAGNOSTIC MODE
ROM VERSION = <version>

2

Press ENTER.

DIAGNOSTIC MODE
SELECT MENU(

←  →)

3

Press 0, 1.

SW # =

4

Enter the SW No. (2 digits) to be changed.

SW # = 10

5

Press 

← / → to shift the cursor to the bit to be

changed. (The left edge is Bit No. 1.)

SW10 = 00010101
bit # = 12345678

6

Press FUNCTION to highlight the bit in the cursor
position.

SW10 = 10010101
bit # = 12345678

7

Press ENTER to register.

SW # =

Return to Step 3.
Press STOP to exit from the mode.

1

No signal ( OFF HOOK state)

2

DTMF

(0,1,2,3,4,5,6,7,8,9,*,#)

3

14400 bps (V.17)

(00000000b, 11111111b, 01010101b)

4

12000 bps (V.17)

(00000000b, 11111111b, 01010101b)

5

9600 bps (V.17)

(00000000b, 11111111b, 01010101b)

6

7200 bps (V.17)

(00000000b, 11111111b, 01010101b)

7

9600 bps (V.29)

(00000000b, 11111111b, 01010101b)

8

7200 bps (V.29)

(00000000b, 11111111b, 01010101b)

9

4800 bps (V27ter)

(00000000b, 11111111b, 01010101b)

10

2400 bps (V27ter)

(00000000b, 11111111b, 01010101b)

11

300 bps (FLAG)

(00000000b, 11111111b, 01010101b)

12

2100 Hz (CED)

13

1100 Hz (CNG)

AR-F151

9  – 15