Read Sharp R-8000GK Service Manual online
R-8000GK
27
DOOR PANEL ASSEMBLY, LATCH HEAD RIGHT
AND LATCH HEAD LEFT
AND LATCH HEAD LEFT
10. Remove the fourteen (14) screws holding the door panel
assembly to the door frame.
11. Remove the door panel assembly from the door frame.
12. Remove the one (1) screw holding the latch head right to the
12. Remove the one (1) screw holding the latch head right to the
door panel assembly.
13. Remove the latch spring right from the latch head right and
the handle lever.
14. Now, the latch head right is free.
15. Remove the one (1) screw holding the latch head left to the
15. Remove the one (1) screw holding the latch head left to the
door panel assembly.
16. Remove the latch spring left from the latch head left and the
handle lever.
17. Now, the latch head left is free.
18. Release the two (2) handle springs from the two (2) handle
18. Release the two (2) handle springs from the two (2) handle
levers.
19. Pull out the two (2) handle pins from the two (2) handle levers.
20. Remove the two (2) handle levers and two (2) handle springs
20. Remove the two (2) handle levers and two (2) handle springs
from the door panel.
21. Now, the door panel is free.
MIDDLE DOOR GLASS
22. Remove the two (2) screws holding the glass mounting angle
B to the door frame.
23. Remove the middle door glass from the door frame.
24. Now, the middle door glass is free.
24. Now, the middle door glass is free.
FRONT DOOR GLASS
25. Remove each two (2) screws holding the two glass mounting
angles A to the door frame.
26. Remove the two (2) glass mounting angles A from the door
frame.
27. To release the two (2) tabs holding the lower end of the front
door glass, slide the front door glass upward.
28. Release the three (3) tabs holding the upper end of the front
door glass and remove the front door glass from the door
frame.
frame.
29. Now, the front door glass is free.
Figure C-8. Door Disassembly
Choke
Cover
Cover
Door
Frame
Frame
Door Panel
Assembly
Assembly
Putty Knife
Control panel assembly
1. CARRY OUT 3D CHECKS.
2. Disconnect the harness assembly from the connector CN-G
on the power unit.
3. Remove the four (4) screws holding the control panel assembly
to the oven cavity front plate.
4. Slide the control panel assembly leftward to release the eight
(8) tabs of the control panel assembly from the oven cavity
front plate.
front plate.
5. Now, the control panel assembly is free.
CPU unit
6. Remove the four (4) screws holding the panel angle to the
panel sub assembly.
7. Release the panel angle from the two (2) tabs of the panel sub
assembly first.
8. Pull out the panel angle from the panel sub assembly and
remove it.
9. Disconnect the harness from the connector CN-J on the CPU
unit.
10. Disconnect the harness assembly from the connector CN-H
on the CPU unit.
11. Remove the seven (7) screws holding the CPU unit to the
panel sub assembly.
CONTROL PANEL ASSEMBLY, CPU UNIT AND CONTROL UNIT REMOVAL
12. Now, the CPU unit is free.
Control unit
11. Remove the eleven (11) screws holding the control unit to the
panel sub assembly.
12. Now, the control unit is free.
NOTE: After the panel angle is removed from the panel sub
NOTE: After the panel angle is removed from the panel sub
assembly, it is can be found that the bottom side of the
panel sub assembly is transformed by heat. But it is not
abnormal and no problem to use the oven.
panel sub assembly is transformed by heat. But it is not
abnormal and no problem to use the oven.
Figure C-9. Panel Angle Removal
Tabs
Screw
Screw
Screw
Screw
Panel angl
Panel sub assembly
Bottom side of
panel sub assembly
panel sub assembly
Click on the first or last page to see other R-8000GK service manuals if exist.