R-24AT (serv.man4). 2012 Revision - Sharp Home Appliance User Guide / Operation Manual. Page 6

A31845,SUK R22AT/24AT O/M

!

1       Remove all packing materials. Remove the protective

film (blue film) from the outer case cabinet (if covered).
Do not remove the plastic film from the inside of the
oven window as this protects it from dirt.

2       Place oven on a secure, level surface, strong enough

to take the oven weight, plus the heaviest item likely
to be cooked in the oven.

  Do not place this oven in a position which is not easily

accessible. To position the oven too high can be
dangerous because food can not be removed safely.

3    Ensure there is a minimum free space above the

oven of 25 cm.

4      Do not place the oven where heat, moisture or high

humidity are generated, (for example, near or above
a  conventional oven) or near combustible materials
(for example, curtains). Do not block or obstruct air
vent openings, as obstructions may ignite due to
the emission of hot air.

  Make sure the power supply cord is undamaged and

that it does not run under the oven or over any hot or
sharp surfaces.

  The socket must be readily accessible so that it can

be easily unplugged in an emergency.

  Do not use the oven outdoors.

  Two same oven models can be installed together by

placing one on top of another. Follow these
instructions.

8-1) Place the oven A and position the oven B on top of

the oven A as shown in the figure A.

8-2) Remove the single screw (a) holding the mounting

plate A to the rear cabinet of the oven A. And remove
the mounting plate A.

8-3) Remove the single screw (b) from the rear cabinet

of the oven B, as shown in the figure A.

8-4) Reinstall the mounting plate A to the rear cabinet of

the oven B with the single screw (b) removed, as
shown in the figure A.

8-5) Hold the mounting plate A to the rear cabinet of the oven

A with the single screw (a), as shown in the figure A.

8-6) Remove the screw (a) holding the mounting plate B

to the rear cabinet of the oven B. And remove the
mounting plate B from the oven B. See the figure A.

8-7) Install the screw (a) to its position again.
8-8) Remove the screw (c) from the oven A.
8-9) Remove the screw (d) from the oven B.

WARNING:
In situations where two ovens are installed together by
placing one on top of another,

1) Use the two mounting plates for fixing the two ovens.
2) Make sure that the power supply cord is not caught

between the two ovens.

3) Do not install more than one oven on top of another.
4) Do not lose the removed screws.

BUILDING-IN-KIT
This oven is not designed to be built into a kitchen unit.
IMPORTANT! ELECTRICAL CONNECTION
• Do not allow water to come into contact with the

power supply cord or plug.

• Insert the plug properly into the socket as the plug

may otherwise overheat and catch fire.

• Do not connect other appliances to the same socket

using an adaptor plug as it may cause the wiring to
overheat and catch fire.

• If the plug or socket is loose or the power supply

cord is damaged, do not operate the oven, it must be
replaced by the special power cord. Contact your
dealer or a Service Technician appointed by SHARP.
A defective plug, power supply cord or socket may overheat
and catch fire during operation or cause an electrical shock.

• When removing the plug from the socket always grip

the plug, never the mains lead as this may damage the
power supply cord and the connections inside the plug.

• The product is fitted with a non-rewireable (moulded)

plug. Should it not be suitable for the socket outlet in
your kitchen, remove the plug and fit an appropriate
type, observing the wiring code given in "To replace
the mains plug" on page 30.

The fuse from a cut-off plug should be removed and the
plug disposed of in safe manner. Under no circumstances
should the cut-off plug be inserted into a socket outlet as
serious electrical shock may occur. The plug must not be
used without the fuse cover fitted.
When replacing the plug please ensure that you use a BSI
or ASTA approved plug to BS1363, this should be fitted
with a brown coloured 13 amp fuse approved by BSI or
ASTA to BS1362. If you have any doubt about electrical
connection seek the help of a qualified electrician.

!

THIS APPLIANCE MUST BE EARTHED.
To wire an appropriate plug, follow the wiring code given
in "To replace the mains plug" on page 30.

Screw (d)

Screw (c)

Mounting plate B

Rear cabinet

Oven A

Screw (b)

Mounting plate A

Screw (a)

Oven B

Rear cabinet

Screw (a)

8-10) Turn the removed mounting plate B over and then

using the removed screw (c) and (d), attach the
mounting plate B, as shown in the figure A.

SUK R22AT/24AT O/M,1-9

11.12.8, 5:08 PM

5