R-1900M (serv.man14) - Sharp Home Appliance User Guide / Operation Manual. Page 8

7

*  Before operating your new oven, make sure you read and 

understand this operation manual completely.

1) Plug in the oven.

*  The digital display will show “ . “

2) Control panels can only be operated when the door is 

closed.

3) Oven light will go on for 1 minute whenever the door is 

opened or after cooking.

Cancellation:
1.  Cooking data is canceled when keys are not pressed for 

more than three minutes when setting programming.

2.  Cooking stops when the STOP/CLEAR pad is pressed and 

cooking data remains. However if subsequent keys are 
not pressed within three minutes, cooking data will be 
canceled. To resume cooking press the START pad.

3.  Cooking stops when the door is opened and cooking data 

remains. However once the door is closed, cooking data 
will be canceled if subsequent keys are not pressed within 
3 minutes. To resume cooking press the START pad.

4.  Cooking is immediately canceled by pressing the STOP/

CLEAR pad twice.

Press the STOP/CLEAR pad then open the door, check 
food, close the door and press the START pad to continue 
cooking.

Cooking Completion:
When food is not taken out after cooking completion, End will 
be shown in the display until the food is taken out.

HELPFUL TIPS for the Memory Input Method 
The Memory Input Method determines how to input memory numbers for Memory Cooking and Custom Setting and Saving 
memories, therefore follow the method below. Refer to HELPFUL TIPS below as well as in Memory cooking.

1.  Dual Digit Input: Must input two numbers to select a 

memory, even though the fi rst number is 0. Memory 
programming is limited to 0 - 99.

2.  Single Digit Input: Can only input one number to select  

a memory. Memory programming is limited to 0 - 9.

3.  Repeat Digit Input: Input one, two, or three numbers 

to select a memory. Memory programming is limited 
to 0 - 29.

4.  For Repeat Digit Input/Auto Start ON only, push number 

pads within one second of the previous number. 

5.  Regardless of Input Method selected, Counter Check/Clear (Custom Setting 7) and Multiplication Factor for Double/ Triple 

Quantity (Custom Setting 10) only use the Dual Digit Input Method. As for Custom Setting 10,  enter memory number 
after pressing the DOUBLE/TRIPLE QUANTITY pad.

0  

2 

12 

22

0, 0 

0, 2 

1, 2 

2, 2

0  

2

0   

2 

2, 2 

2, 2, 2 

Memory No.

Dual Digit Input

Single Digit Input

Repeat Digit Input

Input Method

Memory

Examples

*  Your oven has 100 memory banks from 0 to 99. Memory 

contents from memory number 0 to 29 are same in Dual, 
Single and Repeat Digit Input methods.

*  Memory 0 - 9 are programmed as factory settings. See 

the table of Programmed Memories on the right side. 
Memory 10 - 99 must be programmed before using 
Memory Cooking.  When a memory  number which has 
not been programmed is entered, End will be shown in 
the display. See Saving Memories page 17 - 21 to program 
a new memory.

Memory No.

Cook time (sec.)

Output power

1

5

100%

2

10

100%

3

20

100%

4

30

100%

5

40

100%

6

50

100%

7

1 min.

100%

8

1 min. 15 sec.

100%

9

1 min. 30 sec.

100%

0

2 min.

100%

R-1900M [EN].indd   Sec1:7

R-1900M [EN].indd   Sec1:7

9/29/08   6:17:07 PM

9/29/08   6:17:07 PM