R-1900M (serv.man14) - Sharp Home Appliance User Guide / Operation Manual. Page 4

3

1. Remove all packing materials. Remove the protective fi lm 

(blue fi lm) from the outer case cabinet (if covered). Do not 
remove the plastic fi lm from the inside of the oven window 
as this protects it from dirt.

2.  Place oven on a secure, level surface, strong enough to take 

the oven weight, plus the heaviest item likely to be cooked in 
the oven.

3. Ensure there is a minimum free space above the oven of 

 

25 cm.

4.  Do not place the oven where heat, moisture or high humidity 

are generated, (for example, near or above a conventional 
oven) or near combustible materials (for example, curtains). 
Do not block or obstruct air vent openings, as obstructions 
may ignite due to the emission of hot air.

5. Make sure the power supply cord is undamaged (See 

Installation next page) and that it does not run under the oven 
or over any hot or sharp surfaces.

6.  The socket must be readily accessible so that it can be easily 

unplugged in an emergency.

7.  Do not use the oven outdoors.
8.  Two ovens can be installed together by placing one on top of 

another. Follow these instructions.
A.  Place oven A in the desired location. Position Oven B on 

top of Oven A as shown in the fi gure.

B.  Remove Screws (a) and Mounting plate A and B from the 

right side of the back of Oven A and B.

C.  Replace Screws (a) removed at step B and tighten them.
D. Remove Screws (b), (c), (d), and (e) and then 

install Mounting Plate A and B which were
removed at step B to the each lower edge of Oven B as 
shown in the fi gure.

E.  Replace Screws (b), (c), (d), and (e) which were removed 

at step D and tighten them.

It is hazardous for anyone other than a Service Technician, 
approved by SHARP to carry out any service or repair operation 
which involves the removal of a cover which gives protection 
against exposure to microwave energy.

•  Do not allow water to come into contact with the power supply 

cord or plug.

•  Insert the plug properly into the socket as the plug may 

otherwise overheat and catch fi re.

•  Do not connect other appliances to the same socket using an 

adaptor plug as it may cause the wiring to overheat and catch 
fi re.

•  If the plug or socket is loose or the power supply cord is 

damaged, do not operate the oven, it must be replaced by the 
special power cord. Contact your dealer or a Service Technician 
appointed by SHARP.

 

A defective plug, power supply cord or socket may overheat 
and catch fi re during operation or cause an electrical shock.

•  When removing the plug from the socket always grip the plug, 

never the mains lead as this may damage the power supply 
cord and the connections inside the plug.

•  The product is fi tted with a non-rewireable (moulded) plug. 

Should it not be suitable for the socket outlet in your kitchen, 
remove the plug and fi t an appropriate type, observing the wiring 
code given in “To replace the mains plug” on page 39.

The fuse from a cut-off plug should be removed and the plug 
disposed of in safe manner. Under no circumstances should the 
cut-off plug be inserted into a socket outlet as serious electrical 
shock may occur. The plug must not be used without the fuse 
cover fi tted.

When replacing the plug please ensure that you use a BSI or 
ASTA approved plug to BS1363, this should be fi tted with a brown 
coloured 13 amp fuse approved by BSI or ASTA to BS1362. If 
you have any doubt about electrical connection seek the help 
of a qualifi ed electrician.

To wire an appropriate plug, follow the wiring code given in 
“To replace the mains plug” on page 39.

Should there be any interference caused by the microwave 
oven to your radio or TV, check that the microwave oven is 
on a different electrical circuit, relocate the radio or TV as far 
away from the oven as feasible or check position and signal of 
receiving antenna.

In situations where two ovens are installed together by placing 
one on top of another, 
1)  Use the two mounting plates for fi xing the two ovens.
2)  Make sure that the power supply cord is not caught between 

the two ovens.

3)  Do not install more than one oven on top of another.
4)  Do not lose the removed screws.

Screw (d)

Screw (e)

Screw (d)

Mounting 
plate B

Screw (a)

Screw (c)

Screw (b)

Mounting 
plate A

Screw (e)

Screw (c)

Screw (b)

Screw (a)

R-1900M [EN].indd   Sec1:3

R-1900M [EN].indd   Sec1:3

9/9/08   2:37:17 PM

9/9/08   2:37:17 PM