AX-1100(R)M, AX-1100(SL)M (serv.man11). Component Replacement And Adjustment Procedure - Sharp Home Appliance Service Manual (repair manual). Page 4

AX1100(R)M

12 – 4

7. Remove the one (1) screw holding the tank joint to the tank cover.

8. Remove the tank joint from the tank cover.

CAUTION: When the joint tube or pump tube L is removed from the

engine unit or tank joint, remained water may bleed from
the engine unit.

9. Loosen the pin band and remove the steam exhaust tube from the

oven cavity.

10.Turn the oven over. 

11.Remove the bottom plate cover by removing the two (2) screws.

12.Disconnect the wire leads from the pump motor.

13.Remove the two (2) screws holding the lower hinge to the bottom

plate, and remove the lower hinge.

14.Remove the one (1) screw holding the tank cover to the bottom

plate (right side).

15.Remove the four (4) screws holding the bottom plate to the oven

cavity.

16.Lift up the bottom plate from the oven.

17.Now, bottom plate is free. But the bottom plate still has the high

voltage capacitor, tube pump assembly, dew tray guide left, dew
tray guide right, steam exhaust duct and back dew guide in it.

1. CARRY OUT 3D CHECKS.

2. Remove the back plate, referring to “BACK PLATE REMOVAL”.

3. The joint tube should be removed from the engine unit assembly

now.

CAUTION: When the joint tube is removed from the engine unit,

remained water may bleed from the engine unit.

4. Remove the wire harness from the heater terminal of engine unit

assembly by removing the tow (2) screws.

5. Disconnect the wire leads from the engine thermal cut-out.

6. Remove the three (3) screws which are holding the engine unit

assembly from inside of the oven cavity.

NOTE: Hold the engine unit with your hand when removing, otherwise

the engine unit will fall.

7. Remove the engine packing B from the engine unit.

8. Remove the one (1) screw holding the thermistor (engine) to the

engine unit assembly.

9. Remove the one (1) screw and the one (1) nut holding the engine

thermo angle to the engine unit assembly.

10.Now, the engine unit assembly is free.

CAUTION: CAUTION: When the new engine unit assembly is

installed, carry out a shakedown operation, referring to
“SHAKEDOWN OPERATION OF NEW ENGINE UNIT
ASSEMBLY”.

NOTE: NOTE: When the new engine unit is installed, the thermistor

(engine) and engine packing B should be reinstalled.

After the new engine unit assembly is installed, carry out the following
three procedures to avoid the error operation.

1. Remove the two (2) screws holding the back plate cover and

remove the back plate cover. This is to cool the engine unit.

2. Fill the water tank with water and carry out the 1st. stage of “DES-

CALE” function, referring to “Descale Function” on page 5-4. (citric
acid or lemon juice are not necessary.)

3. Then, carry out Drain water function (refer to “Drain Water Func-

tion” on page 5-4).

4. At last, fill the water tank with water and carry out Steam high cook-

ing again for about ten (10) minutes. And check that the error does
not appear on the display.

5. If the error is appeared and the oven stops at above step 4, carry

out step 2, step 3 and step 4.

6. After shakedown operation, reinstall the back plate cover with the

two (2) screws.

Inside walls of the engine unit assembly have been painted to protect
the engine unit assembly with special paint. And special paint will shed
water initially. By carrying out Steam cooking, paint can be accus-
tomed to water. If this operation is not carried out, the oven will judge
that there is no water in the tank assembly.

And the display will show the error and then the oven will stop.

Because this oven judges that there is water or not by checking on/off
time ratio of the engine unit assembly.

If paint is not accustomed to water, off time will become longer than on
time. At this time, the oven will judge no water.

1. CARRY OUT 3D CHECKS.

2. Remove the engine unit, referring to “ENGIEN UNIT REMOVAL”.

3. Remove the bottom plate, referring to “BOTTOM PLATE

REMOVAL”.

4. Disconnect the connector of the thermistor (engine) from the con-

nector of the main wire harness.

5. Now, the thermistor (engine) is free.

1. CARRY OUT 3D CHECKS.

2. Disconnect the wire leads from the oven lamp.

3. Remove the one (1) screw holding the oven lamp to the air duct.

4. Remove the oven lamp from the air duct.

5. Now, the oven lamp is free.