Read Sharp ER-A490 (serv.man3) Service Manual online
CHAPTER 3. OP X/Z, X1/Z1,X2/Z2
MODE
MODE
The following categories of reports can be printed by the ECR.
1) OP X/Z reports (individual clerk reports)
2) X1/Z1 reports (Daily sales total X and Z reports)
3) X2/Z2 reports (Periodic total X and Z reports)
To print reports, use the following key entry sequence
JOB#
Range is required
Reading
Resetting
TL
MODE
*
1
OP X/Z
X1/Z1
X2/Z2
F-read
*
3 DATA FOR
REPORT NAME
X
Z
X1
Z1
X2
Z2
X1
*
4
JOB#
READING
NOTE
GENERAL
F
F
F
F
00
—
DEPT/GROUP
F
F
F
10
—
IND. GROUP
F
F
12
GROUP No.
GROUP TOTAL
F
F
13
—
PLU BY RANGE
F
F
F
F
20
PLU CODE
*
2
PLU BY DEPT
F
F
21
DPT CODE
PLU IND. GR.
F
F
22
GROUP No.
PLU GR. TL
F
F
23
—
PLU STOCK
F
24
PLU CODE
*
2
PLU ZERO SALES (ALL)
F
F
27
ALL
(DEPT)
F
F
27
DPT CODE
PLU PRICE CATEGORY
F
F
29
PRICE
*
2
TRANSACTION
F
F
30
—
TL-ID
F
F
31
—
COMMISSION SALES
F
F
32
—
ALL CASHIER
F
F
F
F
50
—
IND. CASHIER
F
F
F
F
F
F
51
—
HOURLY (ALL)
F
F
60
—
HOURLY
(RANGE)
F
60
TIME
*
2
DAILY NET
F
F
F
70
—
GLU
F
F
80
GLU CODE
*
2
GLU BY CASHIER
F
F
81
—
BALANCE
F
F
82
—
STACKED REP
F
F
F
F
90, 91
—
*
1
X1: Daily X report
Z1: Daily Z report
X2: Periodic X report
Z2: Periodic Z report
Stop of printing reports:
The printing of all reports can be stopped by the following operation.
The printing of all reports can be stopped by the following operation.
Set the mode switch to "MRG" to cancel.
Note) When the printing is stopped, the consecutive number or Z
*
1
X1: Daily X report
X2: Periodic X report
X2: Periodic X report
Z1: Daily Z report
Z2: Periodic Z report
Z2: Periodic Z report
*
2
PLU code range can be specified by entering the start and end
numbers according to the following procedure. When specifying
a single time interval, PLU code, the start number has only to be
entered.
numbers according to the following procedure. When specifying
a single time interval, PLU code, the start number has only to be
entered.
*
3
When 2 is entered in the third digit of a job code, periodic reports
are printed.
Example: Daily general report; job code 100
are printed.
Example: Daily general report; job code 100
Periodic general report; job code 200
*
4
Reading display only
→
KEY
→
CL
(Display
amount) (Display
initialize)
KEY
DEPT
= DEPTn key
CID
=
⊗
key
Daily Net = ST key
•
An individual report is printed on the receipt and journal when the
TL key is pressed.
TL key is pressed.
•
Pressing the decimal point key just after the enery of a job code
clears the corresponding data in the ECR. (Z report)
(When printing those reports for which no Z reports can be taken,
the decimal point key cannot be pressed after the entry of a job
code.)
clears the corresponding data in the ECR. (Z report)
(When printing those reports for which no Z reports can be taken,
the decimal point key cannot be pressed after the entry of a job
code.)
•
When the decimal point key is not pressed after the entry of a job
code, the corresponding data is held in the ECR. (X report)
code, the corresponding data is held in the ECR. (X report)
XXXX
All
Start No.
XXXX
End No.
54