DV-S15 (serv.man7). Cabinet disassembly instructions - Sharp DVD Service Manual (repair manual)

dv-s15 (serv.man7) service manual
Model
DV-S15 (serv.man7)
Pages
3 Few pages! See other manuals at the bottom of the first or last page.
Size
191.81 KB
Type
PDF
Document
Service Manual
Brand
Device
DVD / Cabinet disassembly instructions
File
dv-s15-sm7.pdf
Date

Read Sharp DV-S15 (serv.man7) Service Manual online

1-6-1
E56H0DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
This flowchart indicates the disassembly steps to gain
access to item(s) to be serviced. When reassembling,
follow the steps in reverse order. Bend, route, and dress
the cables as they were originally.
1 : Identification (location) No. of parts in the figures
2 : Name of the part
3 : Figure Number for reference
4 : Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or de-
soldered.
P=Spring, L=Locking Tab, S=Screw,
CN=Connector,
*=Unhook, Unlock, Release, Unplug, or Desolder
e.g. 5(S-1) = five Screws (S-1),
2(L-2) = two Locking Tabs (L-2)
5 : Refer to "Reference Notes."
Reference Notes
CAUTION 1: Locking Tabs (L-1), (L-2) and (L-3) are
fragile. Be careful not to break them.
1-1. Connect the wall plug to an AC outlet and press the
OPEN/CLOSE button to open the Tray.
1-2. Remove the Tray Panel by releasing two Locking
Tabs (L-1).
1-3. Press the OPEN/CLOSE button again to close the
Tray.
1-4. Press the POWER button to turn the power off.
1-5. Unplug an AC Cord.
1-6. Release two Locking Tabs (L-2). Then, release
five Locking Tabs (L-3) (to do this, first release two
Locking Tabs (A) at the bottom, and then three
Locking Tabs (B) at the side.) (Fig. 2)
CAUTION 2: Electrostatic breakdown of the laser diode
in the optical system block may occur as a potential
difference caused by electrostatic charge accumulated
on cloth, human body etc., during unpacking or repair
work.
To avoid damage of pickup follow next procedures.
2-1. Slide out the pickup unit as shown in Fig. 4.
2-2. Short the three short lands of FPC cable with
solder before removing the FFC cable (CN101)
from it. If you disconnect the FFC cable (CN101),
the laser diode of pickup will be destroyed. (Fig. 4)
2-3. Disconnect Connector (CN401). Remove three
Screws (S-2) and lift the DVD Mecha. (Fig. 3)
CAUTION 3: When reassembling, confirm the FFC
cable (CN101) is connected completely. Then remove
the solder from the three short lands of FPC cable.
(Fig. 4)
2. Disassembly Method
REMOVAL
ID/
LOC.
No.
Fig.
No.
REMOVE/
*UNHOOK/UNLOCK/
RELEASE/UNPLUG/
DESOLDER
Note
PART
[1] Top Cover
1
5(S-1)
-
[2] Front
2
*2(L-1), Tray Panel,
1-1
Assembly
*2(L-2), *5(L-3)
1-2
1-3
1-4
1-5
1-6
[3] DVD
3,4
3(S-2)
2
Mecha
*CN101, *CN401
2-1
2-2
2-3
3
[4] AV CBA
5
4(S-3), 6(S-4),
-
*2(L-4), *CN1001,
*CN1601
[5] DVD Main
5
3(S-5)
-
CBA Unit
[6] Rear
6
3(S-6)
-
Panel
1
2
3
4
5
[1] Top Cover
[2] Front Assembly
[3] DVD Mecha
[5] DVD Main CBA Unit
[4] AV CBA
[6] Rear Panel
1-6-2
E56H0DC
(S-1)
(S-1)
[1] Top Cover
(S-1)
Fig. 1
[2] Front Assembly
Tray Panel
(A)
(A)
(L-3)
(L-2)
(L-1)
(L-1)
(B)
Fig. 2
[3] DVD Mecha
(S-2)
(S-2)
CN101
CN401
Fig. 3
View for B
Pickup Unit 
C
B
Short the three short 
lands by soldering
View for C
Slide
View for A
OR
Short the three short lands by soldering
DVD Mecha
A
Fig. 4
1-6-3
E56H0DC
[4] AV CBA
[5] DVD Main CBA Unit
(S-5)
(S-5)
(S-3)
(S-4)
(S-3)
CN1601
CN1001
(S-4)
(L-4)
(S-4)
Fig. 5
[6] Rear Panel
(S-6)
Fig. 6
Eject-Bar (Length = approximately 80 mm, Diameter = approximately 3 mm)
Manual 
Eject Hole
DVD Mecha
Tray
Top Case
1
3
2
HOW TO MANUAL EJECT
1. Remove the Top Case.
2. Insert the eject-bar (length = approximately 80 mm,
diameter = approximately 3 mm) into the manual eject
hole on the DVD Mecha. Then, press it until the tray
is ejected.
Page of 3
Display

Download Sharp DV-S15 (serv.man7) Service Manual (Repair Manual)

Here you can read online and download Sharp DV-S15 (serv.man7) Service Manual in PDF. DV-S15 (serv.man7) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp DV-S15 (serv.man7) DVD. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.