DV-S15 (serv.man11). Schematic diagrams - Sharp DVD Service Manual (repair manual)

dv-s15 (serv.man11) service manual
Model
DV-S15 (serv.man11)
Pages
8
Size
1.52 MB
Type
PDF
Document
Service Manual
Brand
Device
DVD / Schematic diagrams
File
dv-s15-sm11.pdf
Date

Read Sharp DV-S15 (serv.man11) Service Manual online

1-10-1
SC-FN2
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics often
pass unnoticed and the protection afforded by them
cannot necessarily be obtained by using replacement
components rated for higher voltage, wattage, etc.
Replacement parts that have these special safety
characteristics are identified in this manual and its
supplements; electrical components having such
features are identified by the mark " ! " in the schematic
diagram and the parts list. Before replacing any of these
components, read the parts list in this manual carefully.
The use of substitute replacement parts that do not
have the same safety characteristics as specified in the
parts list may create shock, fire, or other hazards.
Capacitor Temperature Markings
Mark
Capacity
change rate
Standard 
temperature
Temperature
range
(B)
(F)
±10%
+30 - 80%
±15%
+30 - 80%
20
°C
20
°C
20
°C
20
°C
-25~+85
°C
-25~+85
°C
-25~+85
°C
-10~+70
°C
(SR)
(Z)
Capacitors and transistors are represented by the
following symbols.
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS
Notes:
1. Do not use the part number shown on these draw-
ings for ordering. The correct part number is shown
in the parts list, and may be slightly different or
amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K=10
3
,
M=10
6
).
3. Resistor wattages are 1/4W or 1/6W  unless other-
wise specified.
4. All capacitance values are indicated in 
µF
(P=10
-6
 
µF).
5. All voltages are DC voltages unless otherwise speci-
fied.
6. Electrical parts such as capacitors, connectors, di-
odes, IC's, transistors, resistors, switches, and fuses
are identified by four digits. The first two digits are
not shown for each component. In each block of the
diagram, there is a note such as shown below to
indicate these abbreviated two digits.
(Top View) (Bottom View)
(Bottom View)
Electrolytic Capacitor
+
Transistor or Digital Transistor
NPN Transistor
PNP Transistor
NPN Digital Transistor
PNP Digital
Transistor
(Top View)
(Top View)
E C B
E    C    B
Digital Transistor
CBA Symbols 
Schematic Diagram Symbols 
E C B
(Top View)
(Top View)
E C B
E C B
1-10-2
SC-FN2
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING
PAGES:
1. CAUTION:
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective
before you connect the AC plug to the AC power supply.  Otherwise it may cause some components in the power
supply circuit to fail.
3. Note:
(1) Do not use the part number shown on the drawings for ordering.  The correct part number is shown in the parts
list, and may be slightly different or amended since the drawings were prepared.
(2) To maintain original function and reliability of repaired units, use only original replacement parts which are listed
with their part numbers in the parts list section of the service manual.
4. Wire Connectors
(1) Prefix symbol “CN” means “connector” (can disconnect and reconnect).
(2) Prefix symbol “CL” means “wire-solder holes of the PCB” (wire is soldered directly).
5. Voltage indications for PLAY modes on the schematics are as shown below:
2
3
1
 5.0
PLAY mode
5.0
Unit: Volts
Indicates that the voltage
is not consistent here.
6. How to read converged lines
1-D3
   Distinction 
Area
 Line 
Number
(1 to 3 digits)
 Examples:
  1. "1-D3" means that line number "1" goes to area "D3".
  2. "1-B1" means that line number "1" goes to area "B1".
 
3
2
1
A
B
C
D
1-B1
1-D3
AREA D3
AREA B1
7. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
1-10-3
1-10-4
1-10-5
E56H0SCD1
DVD Main 1/4 Schematic Diagram
MAIN 1/4
Ref No.
Position
IC101
C-4
IC102
F-5
IC103
B-3
IC301
E-2
Q101
B-3
Q102
B-3
CN101
A-4
CN302
G-2
CN501
A-2
CONNECTORS
ICS
TRANSISTORS
DVD Main 2/4 Schematic Diagram
1-10-6
1-10-7
1-10-8
E56H0SCD2
MAIN 2/4
Ref No.
Position
IC201
N-2
IC401
I-3
Q401
I-3
CN201
N-1
CN401
H-4
CONNECTORS
ICS
TRANSISTOR
Page of 8
Display

Download Sharp DV-S15 (serv.man11) Service Manual (Repair Manual)

Here you can read online and download Sharp DV-S15 (serv.man11) Service Manual in PDF. DV-S15 (serv.man11) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp DV-S15 (serv.man11) DVD. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.