Read Sharp SD-EX200 User Guide / Operation Manual online
22
SD-EX200H_uk.fm
03/2/18
SD-EX200H
RD
S Ra
dio
- Usi
n
g
th
e
Radio Da
ta
S
y
stem (RDS
) -
Using the Radio Data System (RDS) (continued)
!
Using the Auto Station Programme Mem-
ory (ASPM)
ory (ASPM)
To stop the ASPM operation before it is complete:
Press the ASPM button whilst it is scanning for stations.
The stations which are already stored in memory will be kept there.
The stations which are already stored in memory will be kept there.
Notes:
"
If the same station is broadcasting on different frequencies, the strongest fre-
quency will be stored in memory.
quency will be stored in memory.
"
Any station which has the same frequency as one stored in memory will not be
stored.
stored.
"
If 40 stations have already been stored in memory, the scan will be aborted. If you
want to redo the ASPM operation, erase the preset memory.
want to redo the ASPM operation, erase the preset memory.
"
If the RDS signals are very weak, station names may not be stored in memory.
To erase all of the contents of preset memory:
To store a station name again if the wrong name was stored in mem-
ory:
ory:
It may be impossible to store station names in memory using the ASPM function if
there is lots of noise or if the signal is too weak. In this case, perform as follows.
there is lots of noise or if the signal is too weak. In this case, perform as follows.
Notes:
"
The same station name can be stored in different channels.
"
In a certain area or during certain time periods, the station names may temporarily
be different.
be different.
Whilst in the ASPM operation mode, the
tuner will automatically search for new
RDS stations. Up to 40 stations can be
stored.
If you have already stored some stations in
memory, the number of new stations you
can store will be less.
tuner will automatically search for new
RDS stations. Up to 40 stations can be
stored.
If you have already stored some stations in
memory, the number of new stations you
can store will be less.
1
Press the TUNER (BAND) button to select the FM band.
2
Press and hold down the RDS ASPM button for at least 3 seconds.
1
After "ASPM" has flashed for about 4 seconds, scanning will start (87.50 -
108.00 MHz).
108.00 MHz).
2
When an RDS station is found, "RDS" will appear for a short time and the sta-
tion will be stored in memory.
tion will be stored in memory.
3
After scanning, the number of stations stored in memory will be displayed for
4 seconds, and then "END" will appear for 4 seconds.
4 seconds, and then "END" will appear for 4 seconds.
1
Press the ON/STAND-BY button to enter the power stand-by mode.
2
Whilst pressing down the TUNER (BAND) button and the VOLUME (-) button,
press the ON/STAND-BY button until "TUNER CL" and "COMPLETE" appear.
press the ON/STAND-BY button until "TUNER CL" and "COMPLETE" appear.
1
Press the TUNER PRESET ( or ) button to check whether the names are cor-
rect.
rect.
2
If you find a wrong name during receiving the station. Wait until the correct name
will be displayed. And then press the ENTER button.
will be displayed. And then press the ENTER button.
3
Within 5 seconds, press the TUNER PRESET ( or ) button to display the preset
channel to be corrected again.
channel to be corrected again.
4
Within 5 seconds, press the ENTER button.
"
The new station name has been stored in memory correctly.
Click on the first or last page to see other SD-EX200 service manuals if exist.