Read Panasonic TH-65LFB70E Service Manual online
NW Mode
Note:
To use the network function, set each “Network Setup” setting and make sure to set the “Control I/F” to “LAN”
or “RS232C”
Select the NW mode by Up/Down buton on the remote control at the front page of CAT mode and then press the Action
button on the remote control.
*1: If you move a cursor to “Firmware” and press an Action button, “Only receiving side information display” and
“Receiving side / Transmitting side information simultaneous display” can be switched.
*2: The value of “Max Count” is resettable if you move a cursor to “Max Count” and press an Action button.
[Example of Receiving / Transmitting side information simultaneous display]
To exit the NW mode, press the R button on the remote control.
TEST OK
Version xx.xx/xx.xx
MAC(WIRED) xx:xx:xx:xx:xx:xx
MAC(WIRELESS) xx:xx:xx:xx:xx:xx
Control I/F Select xxxxxxxxxxxxxxx
DIGITAL LINK
Firmware xx.xx.xxx
Link Status No link
HDMI Status HDMI on
BER V_/A_/B_/C_
Max Count A X/B X/C X/D X
Est. Cable Length x (m)
Signal Quality
A - xx (dB)
B - xx (dB)
C - xx (dB)
D - xx (dB)
Min - xx (dB)
Max - xx (dB)
Model Name xxxxxxxx
MAC(WIRELESS) xx:xx:xx:xx:xx:xx
Control I/F Select xxxxxxxxxxxxxxx
DIGITAL LINK
Firmware xx.xx.xxx
Link Status No link
HDMI Status HDMI on
BER V_/A_/B_/C_
Max Count A X/B X/C X/D X
Est. Cable Length x (m)
Signal Quality
A - xx (dB)
B - xx (dB)
C - xx (dB)
D - xx (dB)
Min - xx (dB)
Max - xx (dB)
Model Name xxxxxxxx
NW
*1
*2
Press the Action button to start TEST (Check of Ping).
Check to show “OK” in TEST column.
If “G_NG” shows, it is failure for Ping process.
If “L_NG” shows, it is failure for Link process.
If “L_NG” shows, it is failure for Link process.
Software Version
DIGITAL LINK: Checking signal quality
Mac address
Control I/F Select
Link Status : Connection state
No link : No connection
DIGITAL LINK : In DIGITAL LINK operation
Ethernet : In Ethernal operation
No link : No connection
DIGITAL LINK : In DIGITAL LINK operation
Ethernet : In Ethernal operation
HDMI Status : Display the information of HDMI ON/OFF and HDCP
No HDMI : Can not be recognized as a signal of the HDMI
HDMI on : Non HDCP HDMI signal
HDCP on : HDCP HDMI signal
No HDMI : Can not be recognized as a signal of the HDMI
HDMI on : Non HDCP HDMI signal
HDCP on : HDCP HDMI signal
Error ratio of the transmission path information
V : VIDEO BER
A : AUDIO BER
B : BLANK BER
C : CONTROL BER (Max: 10)
V : VIDEO BER
A : AUDIO BER
B : BLANK BER
C : CONTROL BER (Max: 10)
Standard of momentary signal quality aggravation
When it is over 64, the imagine may have broken off.
(Max: 255)
When it is over 64, the imagine may have broken off.
(Max: 255)
Signal Quality: Display the signal quality at the time of
DIGITAL LINK operation
OK/LOW/NG is displayed as each
Channel (A,B,C,D, Min, Max)
-12 dB or more : Normal receivable range
-11 to -8 dB : Partial damage of data (possible image output)
-7 dBor less : Synchronization disorder occurrence
(impossible image output)
DIGITAL LINK operation
OK/LOW/NG is displayed as each
Channel (A,B,C,D, Min, Max)
-12 dB or more : Normal receivable range
-11 to -8 dB : Partial damage of data (possible image output)
-7 dBor less : Synchronization disorder occurrence
(impossible image output)
TEST OK
Version xx.xx/xx.xx
MAC(WIRED) xx:xx:xx:xx:xx:xx
MAC(WIRELESS) xx:xx:xx:xx:xx:xx
Control I/F Select xxxxxxxxxxxxxxx
DIGITAL LINK
Firmware xx.xx.xxx
MAC(WIRELESS) xx:xx:xx:xx:xx:xx
Control I/F Select xxxxxxxxxxxxxxx
DIGITAL LINK
Firmware xx.xx.xxx
/ xx.xx.xxx
Link Status DIGITAL LINK
/DIGITAL LINK
HDMI Status HDMI on
/ HDMI on
BER V_/A_/B_/C_
/T_
Max Count A X/B X/C X/D X
Est. Cable Length x (m)
Signal Quality
A - xx (dB)
B - xx (dB)
C - xx (dB)
D - xx (dB)
Min - xx (dB)
Max - xx (dB)
Model Name xxxxxxxx
Est. Cable Length x (m)
Signal Quality
A - xx (dB)
B - xx (dB)
C - xx (dB)
D - xx (dB)
Min - xx (dB)
Max - xx (dB)
Model Name xxxxxxxx
NW
T: total ber (Transmitting side)
Transmitting side information is displayed on right-hand side.
14
Click on the first or last page to see other TH-65LFB70E service manuals if exist.