Read Panasonic TH-65LFB70E Service Manual online
CD Mode
Select the CD mode by Up/Down buton on the remote control at the front page of CAT mode and then press the Mute
button on the remote control more than 3 seconds.
button on the remote control more than 3 seconds.
Memory data change
To exit the CD mode, press the R button on the remote control.
About the serial number display
As for the serial number of A-module for repair, a dummy value is displayed.
* By the set for which A-module was exchanged, a serial number is displayed as [-----]
About the history display of SOS for the power supply system
* By the set for which A-module was exchanged, a serial number is displayed as [-----]
About the history display of SOS for the power supply system
This unit adds the history display (5 times) of power supply failure to the CD mode as PTCT.
By the self check of a signal system, only one history is displayed (After a self check disappears). But PTCT display
5 times of histories (Abnormality of the latest 3 times. First time and second time after shipment) and after a self
check does not disappear.
You can see a detailed history of power failure sometimes.
*About the display contents of PTCT
PTCT : The position of [05] is the first time after shipment.
PTCT : The position of [04] is the second time after shipment.
PTCT : The position of [03] is second from last time.
PTCT : The position of [02] is last time.
PTCT : The position of [01] is the latest.
In [Contents & Check point] of [6.1.2 Power LED Blinking timing chart], the two-digit following PTCT are displayed
by a hexadecimal number.
5 times of histories (Abnormality of the latest 3 times. First time and second time after shipment) and after a self
check does not disappear.
You can see a detailed history of power failure sometimes.
*About the display contents of PTCT
PTCT : The position of [05] is the first time after shipment.
PTCT : The position of [04] is the second time after shipment.
PTCT : The position of [03] is second from last time.
PTCT : The position of [02] is last time.
PTCT : The position of [01] is the latest.
In [Contents & Check point] of [6.1.2 Power LED Blinking timing chart], the two-digit following PTCT are displayed
by a hexadecimal number.
Blinking times
Contents &Check point
Display contents
Ex. 1
4 times
PTCT 04 H09
04
Ex. 2
8 times
PTCT 08 H029
08
0
0
Address
Change by Up/Down buttons on the remote control.
Change by Left/Right buttons on the remote control.
0
0
Data
Change by VOL Up/Down buttons on the remote control.
The data is memorized when switch off the main power.
MONITOR-MCU(50inch) *.****LFB70 OK
MONITOR-EEPROM **.** * BB 73
MONITOR-EEPROM Change Addr 00 01
Data 01 01
MONITOR-FPGA **.**
MONITOR-FRC **
LAN MCU **.**/**.**
HD-BaseT **.**.***
TOUCH PANEL *.*.*.*
LAN-MAC (WIRED) **:**:**:**:**:**
LAN-MAC (WIRELESS) **:**:**:**:**:**
SLOT BOARD EEPROM -- -- -- --
SLOT BOARD --/--/-- -- -- --
SERIAL No **********
PTCT 01. 02. 03. 04. 05.
MONITOR-FPGA **.**
MONITOR-FRC **
LAN MCU **.**/**.**
HD-BaseT **.**.***
TOUCH PANEL *.*.*.*
LAN-MAC (WIRED) **:**:**:**:**:**
LAN-MAC (WIRELESS) **:**:**:**:**:**
SLOT BOARD EEPROM -- -- -- --
SLOT BOARD --/--/-- -- -- --
SERIAL No **********
PTCT 01. 02. 03. 04. 05.
CD
Factory use
New data
Original data
SOS history
PTCT position: [01] [02] [03] [04] [05]
13
Click on the first or last page to see other TH-65LFB70E service manuals if exist.