Read Panasonic PT-RZ670 / PT-RW630 (serv.man14) Other Service Manuals online
SECTION 1 SERVICE INFORMATION
< RZ670/RW630 >
A
A
DG-P.C.Board and FM-P.C.Board are easily damaged by static electricity, please be careful as using an antistatic wrist strap.
2
A
Check the X3501 and peripheral circuit
[Note]
FM Check the loads on 3.3V and 12V power-supply line
●Main microprocessor operation check
FM
Check the cable connector and flexible cable
FM1, FM2, FM3
* Is not bent the pin of connector ?
* Is not aslant insert of FFC cable ?
FM1, FM2, FM3
* Is not bent the pin of connector ?
* Is not aslant insert of FFC cable ?
Connect the cable connector properly
* It replace, if the pin of the connector has bent
* Replace the flexible cable if there is a vertical line
noise on the screen
* It replace, if the pin of the connector has bent
* Replace the flexible cable if there is a vertical line
noise on the screen
E
a
c
h
rel
a
y
board
Check the cable connector
Connector of each relay board
* Is not bent the pin of connector ?
Connector of each relay board
* Is not bent the pin of connector ?
Connect the cable connector properly
* It replace, if the pin of the connector has bent
* It replace, if the pin of the connector has bent
A
Check in order of the following
IC3716(FLASH ROM) and peripheral circuits
IC3721(SRAM) and peripheral circuits
IC3501(MAIN CPU) and peripheral circuits
IC3716(FLASH ROM) and peripheral circuits
IC3721(SRAM) and peripheral circuits
IC3501(MAIN CPU) and peripheral circuits
● DG/FM-P.C.Board operation check
A
Check the voltage of A1 connector
1pin : 3.3V, 3pin : 5V
1pin : 3.3V, 3pin : 5V
Check the cable connector between A1 and P6
Replace the P-P.C.Board
Replace the P-P.C.Board
The voltage of R3826 is 1.2V
Check the IC3821 and peripheral circuit
A
Check the clock waveform
R3622 : 35.455 MHz
R3622 : 35.455 MHz
DG
Power-supply line check <1>
DG1 : TPDG6 = 3.3V, TPDG7 = 5V
DG12 : C6866(+) = 12V, C6894(+) = 3.3V,
C6864(+) = 18V
DG1 : TPDG6 = 3.3V, TPDG7 = 5V
DG12 : C6866(+) = 12V, C6894(+) = 3.3V,
C6864(+) = 18V
DG
P
Check the loads on each power-supply line
Replace the PC-P.C.Board
Replace the PC-P.C.Board
FM
Power-supply line check <2>
FM3 : TP4001(or DG5 5,6,7pin) = 3.3V
FM3 : TP4001(or DG5 5,6,7pin) = 3.3V
: TP4002 (or DG5 2pin) = Approx 12V
(TP4002 is RW/RX model only)
DG
Check the cable connector and flexible cable
(surface) DG1, DG3-DG14, DG16-DG19
(rear surface) DG2 (Board to Board connector)
* Is not bent the pin of connector ?
* Is not aslant insert of FFC cable ?
(surface) DG1, DG3-DG14, DG16-DG19
(rear surface) DG2 (Board to Board connector)
* Is not bent the pin of connector ?
* Is not aslant insert of FFC cable ?
Connect the cable connector properly
* It replace, if the pin of the connector has bent
* It replace, if the pin of the connector has bent
NG
OK
NG
NG
OK
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
INF - 37
Click on the first or last page to see other PT-RZ670 / PT-RW630 (serv.man14) service manuals if exist.