Read Panasonic PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) Service Manual online
PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE
INF-7
6. SELF CHECK
■Self-diagnosing information Displays.
① Main microprocessor Software Version
② Sub microprocessor Software Version
③ Network microprocessor Software Version
④ Geometry Software Version/FPGA Software Version
(No display for DW8300U/DW90XE)
⑤ Emulate setting / Software Version
⑥ Intake Air Temperature (Celsius/Fahrenheit)
⑦ DMD Temperature (Celsius/Fahrenheit)
⑧ Exhaust Air Temperature (Celsius/Fahrenheit)
⑨ Airflow Sensor
(Sensor value/AD conversion value/Correction value)
⑩ LAMP1 Condition (Cumulative Usage Time/ON-OFF)
⑪ LAMP2 Condition (Cumulative Usage Time/ON-OFF)
⑫ Fan Condition (1:
normal /0:stop)
From the left : DMD2/DMD1/Color prism/DMD Exhaust/
Synthetic Mirror/Ballast/Power/Lamp2/
Lamp1/ Intake2/ Intake1/ Exhaust-L/
Exhaust-C/ Exhaust-R/
⑬ Brightness sensor Condition
⑭ Iris Condition
7. POWER ON SHUTTER
- OPEN: Opens the shutter when power ON.
- CLOSE: Closes the shutter when power ON.
8. POWER OFF MESSAGE
Shutter open/close action setting, at the time of the standby operation.
- SHUTTER KEEP: The shutter keeps open or close.
- SHUTTER OPEN: The shutter is opened.
9. ERROR OSD
When I do not watch the error instructions LED of the lamp by a back projection,
the errors of the lamp can be displayed in the OSD.
- ON: OSD does not display the lamp error.
- OFF: OSD display a lamp error.
10. UNIFORMITY
Sets the value of color unevenness correction.
11. CONVERGENCE
When the ingredient of each R/G/B color deviation, revise it electrically.
Specifically, please refer to Clause 1 of SECTION 3 (adjustments).
12. MODEL
After replacing A-PCB, setting the model info.
13. ACF 1) FILTER TYPE ･･･Setting kind of the filter.
- NORMAL: Default setting. (Usually)
- SPECIAL: Sets it when the smoke cut filter is installed.
2) ROLL･･･Rewinds the filter once compulsorily.
14. CLOG SENSOR CALIBRATION
Execute the sensor calibration when EEPROM (IC3108 or IC3109) / A-P.C.Board or Airflow sensor (M2-P.C.Board)
is replaced. Please refer to Clause 1 of SECTION 3 (Adjustments) for the procedure.
* If items ⑥ - ⑭ are indicated with "NG" in red, the
projector has an abnormality now. If the projector has an
abnormality in the past and operates normally now, the
first self-check screen is indicates in red with
"OK".(Except fan error.) Error information is cleared
after exiting from self-check mode.
abnormality in the past and operates normally now, the
first self-check screen is indicates in red with
"OK".(Except fan error.) Error information is cleared
after exiting from self-check mode.
Click on the first or last page to see other PT-DZ8700U / PT-DS8500U / PT-DW8300U / PT-DZ110XE / PT-DS100XE / PT-DW90XE (serv.man11) service manuals if exist.