Read Panasonic UF-490 / UF-4000 / UF-4100 Service Manual online
115
412
G3 RX
B, D
No response within 12 seconds in
NSS/DCS/MPS wait state. (After
transmitting FTT)
NSS/DCS/MPS wait state. (After
transmitting FTT)
Transmitter is defective.
SC PCB is defective.
SC PCB is defective.
414
RCV
(Polling)
B
No response received after
transmitting 3rd NSC.
transmitting 3rd NSC.
Password does not match between
transmitter and receiver.
Transmitter is defective. (No original,
document jam, etc.)
transmitter and receiver.
Transmitter is defective. (No original,
document jam, etc.)
415
XMT
(Polling)
B
Remote side attempted to receive
message from your machine in
polling communication.
message from your machine in
polling communication.
Inform the remote side that your
machine does not have the polling
transmission feature.
machine does not have the polling
transmission feature.
416
RCV
D
Receiver did not detect post
command, such as EOP, MPS,
EOM, etc.
command, such as EOP, MPS,
EOM, etc.
Transmitter is defective.
Line quality is poor. (RTC signal is
distorted due to line noise)
SC PCB is defective.
Line quality is poor. (RTC signal is
distorted due to line noise)
SC PCB is defective.
417
RCV
C
Receiver returned RTN in
response to post message.
response to post message.
Line quality is poor. (There are
excessive errors in received data)
SC PCB is defective.
excessive errors in received data)
SC PCB is defective.
418
RCV
C
Receiver transmitted PIN in
response to PRI-Q from
transmitter. (Transmitting operator
requests voice contact)
response to PRI-Q from
transmitter. (Transmitting operator
requests voice contact)
Line quality is poor. (There are
excessive errors in received data)
SC PCB is defective.
excessive errors in received data)
SC PCB is defective.
420
RCV
B
T1 timer (35 sec.) elapsed without
detecting 300 bps signal.
detecting 300 bps signal.
There is wrong incoming call.(non-
facsimile communication)
Transmitter is defective.
SC PCB is defective.
facsimile communication)
Transmitter is defective.
SC PCB is defective.
421
RCV
B
Busy Tone is detected after
sending NSF Signal.
sending NSF Signal.
Remote station disconnected the line.
Wrong number is dialed.
Wrong number is dialed.
422
XMT
B
Content of NSF (or DIS) or NSC
(or DTC) was invalid.
(or DTC) was invalid.
There is an incompatibility.
427
G3
RCV
B
DCN received to NSF/CSI/DIS
transmitted.
transmitted.
The interface is incompatible.
433
XMT
RCV
RCV
B, D
T.30 Protocol abnormal.
Defective remote station.
434 XMT or RCV
B
CD (response from Modem) did
not turn OFF within 180 sec. after
receiver detected FLAG signal.
not turn OFF within 180 sec. after
receiver detected FLAG signal.
Remote unit is defective.
SC PCB is defective.
SC PCB is defective.
436
G3 RX
C
DCN received after transmitting
FTT.
FTT.
Transmitter is defective or incompatible.
Line quality is poor.
Line quality is poor.
456
RCV
B
Received relay transfer request or
confidential document to distribute
to an end receiving station or all
confidential mailboxes are used.
confidential document to distribute
to an end receiving station or all
confidential mailboxes are used.
459
RCV
C
Failed training in Phase C.
Line quality is poor. (Training signal is
distorted due to line noise)
SC PCB is defective.
distorted due to line noise)
SC PCB is defective.
490
RCV
C
Sum of error lines exceeded the
limit (Function Parameter No. 70)
of 64 lines.
limit (Function Parameter No. 70)
of 64 lines.
Line quality is poor.
SC PCB is defective.
SC PCB is defective.
Fax Information Codes
Code
Mode
Phase
Description of Problem
Cause
Click on the first or last page to see other UF-490 / UF-4000 / UF-4100 service manuals if exist.