Read Panasonic UF-490 (serv.man2) Service Manual online
122
032 V34 TX START
2400-33600bps
Selects the transmission modem start speed for V.34
communication, 33600-2400 bps.
communication, 33600-2400 bps.
033 V34 RX START
2400-33600bps
Selects the receiving modem start speed for V.34
communication, 33600-2400 bps.
communication, 33600-2400 bps.
034 V34 TX Symbol
Rate
2400-3429sr
Selects the transmission symbol rate for V.34, 3429/
3200/3000/2800/2400 sr.
Press “V” or “/\ “ to select the symbol rate.
3200/3000/2800/2400 sr.
Press “V” or “/\ “ to select the symbol rate.
035 V34 RX Symbol
Rate
2400-3429sr
Selects receiving symbol rate for V.34, 3429/3429/
3200/3000/2800/2400 sr.
Press “V” or “/\ “ to select the symbol rate.
3200/3000/2800/2400 sr.
Press “V” or “/\ “ to select the symbol rate.
036 Not Used
037 PROTOCOL
DISPLAY
1 = Off (not displayed)
2 = On (displayed)
2 = On (displayed)
Selects whether to display the modem speed during
communication.
(Press “V” or “/\ “ to display)
communication.
(Press “V” or “/\ “ to display)
038 Not Used
039 FLASH TIME
5 = 50 ms
~
100 = 1000 ms
~
100 = 1000 ms
Selects the pause interval before activating the Flash
key.
key.
040 E/F TIME
(Except for USA
and Canada)
and Canada)
5 = 50 ms
~
100 = 1000 ms
~
100 = 1000 ms
Selects the pause interval before activating the Flash
key.
key.
041 PAUSE TIME
1 = 1 sec.
~
10 = 10 sec.
~
10 = 10 sec.
Selects the pause interval from 1 sec. ~ 10 sec. for
dialing through a switchboard or for international
calls.
dialing through a switchboard or for international
calls.
042 Not Used
043 REDIAL
INTERVAL
0 = no waiting
~
15 = 15 minutes
~
15 = 15 minutes
Selects the redial interval from 0 to 15 minutes in 1
minute steps.
minute steps.
044 REDIAL COUNT 0 = no redial
~
15 = 15 times
15 = 15 times
Selects the redial count from 0 to 15 times in 1 step
intervals.
Note:
intervals.
Note:
In order to comply with the requirements TBR21 in
the EC countries, do not select 15 times.
the EC countries, do not select 15 times.
045 RING DETECT
COUNT
1 = 1 ring
~
9 = 9 rings
~
9 = 9 rings
Selects the ring detection count from 1 to 9 rings in 1
ring step intervals.
ring step intervals.
046 ON-HOOK TIME 0 = 0 sec.
~
90 = 90 sec.
90 = 90 sec.
Selects the on-hook time between sequential
communication calls in 1 second step intervals.
communication calls in 1 second step intervals.
047 RESPONSE
WAIT
1 = 1 sec.
~
90 = 90 sec.
~
90 = 90 sec.
Selects the waiting interval for the response after
completing the dialing.
completing the dialing.
048
049
049
Not Used
050 RING DETECT
MODE
1 = Normal
2 = Rough
2 = Rough
Selects the quality of ringer detection. Use if the line
signal is out of regulation, set to "Rough" so that the
unit may detect the ringing signals.
signal is out of regulation, set to "Rough" so that the
unit may detect the ringing signals.
051 Not Used
052 PULSE RATE
1 = 10 pps
2 = 20 pps
2 = 20 pps
Selects the dial pulse rate 10/20 pps.
Function Parameter Table
No.
Parameter
Selections
Function
Click on the first or last page to see other UF-490 (serv.man2) service manuals if exist.