Read Panasonic DMC-GF2CPP / DMC-GF2CEB / DMC-GF2CEC / DMC-GF2CEE / DMC-GF2CEG / DMC-GF2CGC / DMC-GF2CGD / DMC-GF2CGH / DMC-GF2CGK / DMC-GF2CGN / DMC-GF2CGT / DMC-GF2WEB / DMC-GF2WEG / DMC-GF2WGC / DMC-GF2WGD / DMC-GF2WGH / DMC-GF2WGK / DMC-GF2WGN / DMC-GF2WGT Service Manual online
9
3 Service Navigation
3.1.
Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2.
Important Notice
*When servicing, it is recommended dealing with Clean box. (Refer to "8.2. Clean Box" section of this service manual for details.)
3.2.1.
Camera Body Unit
3.2.1.1.
About VENUS FHD(IC6001) [Located on the Main P.C.B.]:
• The VENUS FHD (IC6001) mounted on the Main P.C.B. consists of FLASH-ROM chip and VENUS chip, both chips are inte-
grated as one-piece with soldered directly.
• When replacing, always replace in pairs. (Units of service parts: integrated (one pair) state.)
NOTE:
• During servicing, do not press down hard on the surface of IC6001.
Fig. S1
3.2.1.2.
About Mount Box Unit (Ref. 3)
1. This Service Manual does not contain the following repair service information for "MOUNT BOX UNIT"(Ref.3), because it
requires special facilities and equipment.
a. Schematic diagram, Block diagram and P.C.B. layout.
b. Parts list for individual parts.
a. Schematic diagram, Block diagram and P.C.B. layout.
b. Parts list for individual parts.
2. If the "MOUNT BOX UNIT" is confirmed as defective, exchange the "MOUNT BOX UNIT" as a unit (supplied as service parts
size).
3. Before exchanging the "MOUNT BOX UNIT", the performances must be carefully checked, by following the "7.Troubleshoot-
ing Guide" section of this service manual.
Important:
1. After replacing the MOUNT BOX UNIT, the mount box data has to be stored to the unit.
When the serial number of the mount box unit which is put on the shield plate of mount box unit is entered to the adjustment
unit, the applicable data is stored into the MAIN P.C.B..
Refer to the adjustment instruction in the adjustment software for details.
unit, the applicable data is stored into the MAIN P.C.B..
Refer to the adjustment instruction in the adjustment software for details.
Fig. S2
2. The full adjustment must be performed after replacing the "MOUNT BOX UNIT", otherwise picture quality can not be meet
with specification.
Click on the first or last page to see other DMC-GF2CPP / DMC-GF2CEB / DMC-GF2CEC / DMC-GF2CEE / DMC-GF2CEG / DMC-GF2CGC / DMC-GF2CGD / DMC-GF2CGH / DMC-GF2CGK / DMC-GF2CGN / DMC-GF2CGT / DMC-GF2WEB / DMC-GF2WEG / DMC-GF2WGC / DMC-GF2WGD / DMC-GF2WGH / DMC-GF2WGK / DMC-GF2WGN / DMC-GF2WGT service manuals if exist.