Read Panasonic WJ-HD100 Service Manual online
– 2 –
!7
REW/FF and Up Button [REW/FF
1
/
2
] [
D
]
Press this button to rewind or fast-forward the recorded
field. The LED lights in the REW/FF mode.
Press this button to move the cursor upward in a setup
menu on the monitor.
field. The LED lights in the REW/FF mode.
Press this button to move the cursor upward in a setup
menu on the monitor.
!8
JogDial [PUSH –
❚❚
PAUSE] [SET]
Press the JogDial to pause or restart playback.
Rotate the JogDial to access the desired field while
rewinding, fast-forward and playing back.
Rotate the JogDial to search the oldest picture recorded
on the disk for playing back in chronological order.
Rotate the JogDial to select a parameter in a setup
menu.
Press the JogDial to enter the selected parameter and
move the cursor to the next position on a setup menu.
Hold down the JogDial to copy still pictures to the
CompactFlash card.
Rotate the JogDial to access the desired field while
rewinding, fast-forward and playing back.
Rotate the JogDial to search the oldest picture recorded
on the disk for playing back in chronological order.
Rotate the JogDial to select a parameter in a setup
menu.
Press the JogDial to enter the selected parameter and
move the cursor to the next position on a setup menu.
Hold down the JogDial to copy still pictures to the
CompactFlash card.
■
Rear View
SIGNAL GND
ALARM
SERIES
RECORD
TIME
ADJUST
REMOTE
MODE
DATA
RS-232C
VIDEO
OUT
IN
OUT
IN
AUDIO
MONITOR OUT
(PLAY)
CAMERA
SW OUT
SW OUT
G
G
G
POWER
ON
OFF
JOG-CLICK
JOG-LEFT
JOG-RIGHT
ALARM SEARCH
STEP
REW/FF
STOP/SETUP
PLAY
REC
OUT
PLAY OUT
REC OUT
AUTO OFF OUT
DISK END OUT
IN
OUT
IN
RECALL
(EXT REC)
OUT
RECOVER OUT
RESET IN
IN
@2
@1 @3
@4
@5
#0
#1 #2 #3
#4
@6
@7
@8 @9
#5
#6 #7
#8
@1
Audio Input Connector [AUDIO IN]
RCA standard jack accepts an unbalanced –10 dB and
10 k
10 k
Ω
line input audio signal supplied from an external
device.
@2
Audio Output Connector [AUDIO OUT]
RCA standard jack supplies an unbalanced –10 dB and
600
600
Ω
line output audio signal to an external device.
@3
Camera Switching Output Connector
[CAMERA SW OUT]
[CAMERA SW OUT]
This jack is for connecting an external device such as a
video multiplexer receiving multiple camera inputs. The
switching signal supplied makes the connected device
switch from one camera to the other. Use this terminal
only when the recording field rate is lower than 10 fps.
video multiplexer receiving multiple camera inputs. The
switching signal supplied makes the connected device
switch from one camera to the other. Use this terminal
only when the recording field rate is lower than 10 fps.
@4
Video Input Connector [VIDEO IN]
This BNC accepts a video signal supplied from a camera
or video multiplexer. A 75
or video multiplexer. A 75
Ω
termination is made unless
the video output terminal is connected.
@5
Video Output Connector [VIDEO OUT]
This BNC supplies a video signal looped through the
video input terminal. Connect with a video monitor to
check the input picture, or the next WJ-HD100 in a
SERIES connection.
video input terminal. Connect with a video monitor to
check the input picture, or the next WJ-HD100 in a
SERIES connection.
@6
Monitor Output Connector
[MONITOR OUT (PLAY)]
[MONITOR OUT (PLAY)]
This BNC supplies playback pictures stored on the hard
disk, or setup windows. Connect with a video monitor.
disk, or setup windows. Connect with a video monitor.
@7
RS-232C Port [RS-232C]
Through this 9-pin D-Sub connector the digital disk
recorder communicates with the personal computer. Use
a reverse type cable for connection with the personal
computer. Protocol and commands are described in
APPENDIX.
recorder communicates with the personal computer. Use
a reverse type cable for connection with the personal
computer. Protocol and commands are described in
APPENDIX.
@8
Data Port [DATA]
Connect with equipment in the PS
•
Data chain or a sys-
tem controller.
@9
Mode Switch [MODE]
Use this switch for setting unit addresses and initializing
all disk contents and setup data.
all disk contents and setup data.
Terminal Board
#00
Remote In Terminal
These are connected with switches for external control
of major operations on the front panel such as JOG-
CLICK, JOG-LEFT, JOG-RIGHT, ALARM SEARCH,
STEP, REW/FF, STOP/SETUP, PLAY and REC.
of major operations on the front panel such as JOG-
CLICK, JOG-LEFT, JOG-RIGHT, ALARM SEARCH,
STEP, REW/FF, STOP/SETUP, PLAY and REC.
#11
Time Adjust Terminal
IN and OUT terminals for synchronizing the internal
clock with connected external devices
clock with connected external devices
Click on the first or last page to see other WJ-HD100 service manuals if exist.