Read JBL JSR 675 User Guide / Operation Manual online
8
1. FM INDOOR ANTENNA
Connect the supplied antenna (the
wire lead) to a 300
wire lead) to a 300
Ω
/75
Ω
adapter
and connect the adapter to the 75
Ω
FM antenna terminal, as shown in the
Rear Panel Connection Diagram.
Change the position of the antenna
until you get the best reception of
your favorite stations.
Rear Panel Connection Diagram.
Change the position of the antenna
until you get the best reception of
your favorite stations.
2. FM OUTDOOR
ANTENNA
ANTENNA
An outdoor FM antenna may be used
to further improve the quality of
reception. Disconnect the indoor
antenna before replacing it with the
outdoor one. A 75
to further improve the quality of
reception. Disconnect the indoor
antenna before replacing it with the
outdoor one. A 75
Ω
/300
Ω
adapter
must be used.
3. AM LOOP ANTENNA
Tune in your favorite AM station and
position the loop antenna for best
reception. Try other stations and find
the position that gives the best overall
reception. When this unit is mounted
in a rack or placed on a shelf with
insufficient space behind, hang the
antenna on a wall in the direction
which gives the best reception.
position the loop antenna for best
reception. Try other stations and find
the position that gives the best overall
reception. When this unit is mounted
in a rack or placed on a shelf with
insufficient space behind, hang the
antenna on a wall in the direction
which gives the best reception.
NOTE:
If noise is heard during AM
reception, move the antenna for bet-
ter reception. To prevent undesired
noise, the AM LOOP ANTENNA
should be located at least 12 inches
(30 cm) away from the remote control
wires.
ter reception. To prevent undesired
noise, the AM LOOP ANTENNA
should be located at least 12 inches
(30 cm) away from the remote control
wires.
4. SYSTEM GROUND
TERMINAL
TERMINAL
To reduce hum to a minimum, connect
the ground lead from your turntable to
this terminal.
the ground lead from your turntable to
this terminal.
5. PHONO INPUT JACKS
Input for a TURNTABLE with an MM
cartridge requiring a 47K ohm of load
impedance. Connect shielded cables
from your phono to the LEFT and
RIGHT input jacks.
cartridge requiring a 47K ohm of load
impedance. Connect shielded cables
from your phono to the LEFT and
RIGHT input jacks.
NOTE:
Do not place your
TURNTABLE on a speaker enclosure.
This will avoid howling caused by
transmission of the speaker vibration
to the TURNTABLE.
This will avoid howling caused by
transmission of the speaker vibration
to the TURNTABLE.
6. TV/AUX INPUT JACKS
This extra stereo input is provided for
any source you want to hear. An
additional compact disc player, a
tape recorder, a video cassette
recorder (VCR) etc., can be plugged
into these jacks.
any source you want to hear. An
additional compact disc player, a
tape recorder, a video cassette
recorder (VCR) etc., can be plugged
into these jacks.
7. CD INPUT JACKS
Connect the output cables of a
compact disc player to these jacks.
compact disc player to these jacks.
8. TAPE 1 PLAY JACKS
Connect the line output of your
CASSETTE DECK to these jacks.
CASSETTE DECK to these jacks.
9. TAPE 1 REC JACKS
Connect the line input of your
CASSETTE DECK to these jacks.
CASSETTE DECK to these jacks.
10. TAPE 2 MONITOR
PLAY JACKS
PLAY JACKS
Connect the line output of your
CASSETTE DECK to these jacks. This
input may be connected to the line
output of the audio processor like an
optional graphic equalizer or a Digital
Signal Processor.
CASSETTE DECK to these jacks. This
input may be connected to the line
output of the audio processor like an
optional graphic equalizer or a Digital
Signal Processor.
11. TAPE 2 MONITOR REC
JACKS
JACKS
Connect the line input of your
CASSETTE DECK to these jacks. EQ
controls, loudness and volume settings
have no effect on the signal from this
output for recording. To monitor this
input source while recording, press the
TAPE 2 MON button (MONITOR ON
position). These REC jacks may be
used for the line input of the audio
processor like an optional graphic
equalizer or a Digital Signal Processor.
CASSETTE DECK to these jacks. EQ
controls, loudness and volume settings
have no effect on the signal from this
output for recording. To monitor this
input source while recording, press the
TAPE 2 MON button (MONITOR ON
position). These REC jacks may be
used for the line input of the audio
processor like an optional graphic
equalizer or a Digital Signal Processor.
AM LOOP ANTENNA SETTING
Stand and place it on a shelf
or hang it on a wall.
or hang it on a wall.
LEG
Rear Panel Connections
JSR675 OM (230V) 7/28/98 10:08 AM Page 10
Click on the first or last page to see other JSR 675 service manuals if exist.