Read JBL JSR 655 User Guide / Operation Manual online
8
1. FM INDOOR ANTENNA
Connect the supplied antenna (the
wire lead) to a 300
wire lead) to a 300
Ω
/75
Ω
adapter
and connect the adapter to the 75
Ω
T-shaped FM antenna terminal, as
shown in the Rear Panel Connection
Diagram. Change the position of the
antenna until you get the best recep-
tion of your favorite stations.
shown in the Rear Panel Connection
Diagram. Change the position of the
antenna until you get the best recep-
tion of your favorite stations.
2. FM OUTDOOR
ANTENNA
ANTENNA
An outdoor FM antenna may be used
to further improve the quality of
reception. Disconnect the indoor
antenna before replacing it with the
outdoor one. A 75
to further improve the quality of
reception. Disconnect the indoor
antenna before replacing it with the
outdoor one. A 75
Ω
/300
Ω
adapter
must be used.
3. AM LOOP ANTENNA
Tune in your favorite AM station and
position the loop antenna for best
reception. Try other stations and find
the position that gives the best overall
reception. When this unit is mounted
in a rack or placed on a shelf with
insufficient space behind, hang the
antenna on a wall in the direction
which gives the best reception.
position the loop antenna for best
reception. Try other stations and find
the position that gives the best overall
reception. When this unit is mounted
in a rack or placed on a shelf with
insufficient space behind, hang the
antenna on a wall in the direction
which gives the best reception.
NOTE:
If noise is heard during AM
reception, move the antenna for bet-
ter reception. To prevent undesired
noise, the AM LOOP ANTENNA
should be located at least 30 cm
away from the remote control wiring.
ter reception. To prevent undesired
noise, the AM LOOP ANTENNA
should be located at least 30 cm
away from the remote control wiring.
4. SYSTEM GROUND
TERMINAL
TERMINAL
To reduce hum to a minimum, con-
nect the ground lead from your
turntable to this terminal.
nect the ground lead from your
turntable to this terminal.
5. PHONO INPUT JACKS
Input for TURNTABLE with an MM
cartridge having 47K ohms of load
impedance. Connect shielded cables
from your phono to the LEFT and
RIGHT input jacks.
cartridge having 47K ohms of load
impedance. Connect shielded cables
from your phono to the LEFT and
RIGHT input jacks.
NOTE:
Do not place your
TURNTABLE on a speaker enclosure.
This will avoid howling caused by
transmission of the speaker vibration
to the TURNTABLE.
This will avoid howling caused by
transmission of the speaker vibration
to the TURNTABLE.
6. TV/AUX INPUT JACKS
This extra stereo input is provided for
any source you want to hear. An
additional compact disc player, a
tape recorder, a video cassette
recorder (VCR) etc., can be plugged
into these jacks.
any source you want to hear. An
additional compact disc player, a
tape recorder, a video cassette
recorder (VCR) etc., can be plugged
into these jacks.
7. CD INPUT JACKS
Connect the output cables of a com-
pact disc player to these jacks.
pact disc player to these jacks.
8. TAPE 1 PLAY JACKS
Connect the line output of your
CASSETTE DECK to these jacks.
CASSETTE DECK to these jacks.
9. TAPE 1 REC JACKS
Connect the line input of your
CASSETTE DECK to these jacks.
CASSETTE DECK to these jacks.
10. TAPE 2 MONITOR
PLAY JACKS
PLAY JACKS
Connect the line output of your
CASSETTE DECK to these jacks. This
input may be connected to the line
output of the audio processor like an
optional graphic equalizer or a Digital
Signal Processor.
CASSETTE DECK to these jacks. This
input may be connected to the line
output of the audio processor like an
optional graphic equalizer or a Digital
Signal Processor.
11. TAPE 2 MONITOR REC
JACKS
JACKS
Connect the line input of your
CASSETTE DECK to these jacks. EQ
controls, loudness and volume set-
tings have no effect on the signal
from this output for recording. To
monitor this input source while
recording, press the TAPE 2 MONI-
TOR button (MONITOR ON position).
These REC jacks may be used for the
line input of the audio processor like
an optional graphic equalizer or a
Digital Signal Processor.
CASSETTE DECK to these jacks. EQ
controls, loudness and volume set-
tings have no effect on the signal
from this output for recording. To
monitor this input source while
recording, press the TAPE 2 MONI-
TOR button (MONITOR ON position).
These REC jacks may be used for the
line input of the audio processor like
an optional graphic equalizer or a
Digital Signal Processor.
AM LOOP ANTENNA SETTING
Stand and place it on a shelf
or hang it on a wall.
or hang it on a wall.
LEG
Rear Panel Connections
JSR655om (a) qx 7/28/98 9:54 AM Page 10
Click on the first or last page to see other JSR 655 service manuals if exist.