Read Harman Kardon ESQUIRE EMC - CB Certificate online
Page 77 of 84 Report No. EFSN13070410E-1
TRF No. IEC60950_1C
Clause
Requirement - Test
Result - Remark
Verdict
2.3.1
For TNV-2 and TNV-3 circuits with other than ringing
signals and with voltages exceeding 42.4 Vpeak or 60
Vd.c., the maximum acceptable current through a 2000
ohm resistor (or greater) connected across the voltage
source with other loads disconnected is 7.1 mA peak
or 30 mA d.c. under normal operating conditions
signals and with voltages exceeding 42.4 Vpeak or 60
Vd.c., the maximum acceptable current through a 2000
ohm resistor (or greater) connected across the voltage
source with other loads disconnected is 7.1 mA peak
or 30 mA d.c. under normal operating conditions
N/A
2.3.2.1
In the event of a single fault between TNV and SELV
circuits, the limits of 2.2.3 apply to SELV Circuits and
accessible conductive parts.
circuits, the limits of 2.2.3 apply to SELV Circuits and
accessible conductive parts.
N/A
2.6.3.4
Protective bonding conductors of non-standard
protective bonding constructions (e.g., printed circuit
traces) may be subjected to the additional limited short
circuit test conditions specified.
protective bonding constructions (e.g., printed circuit
traces) may be subjected to the additional limited short
circuit test conditions specified.
N/A
4.2.8.1
Enclosures around CRTs with a face diameter of 160
mm or more reduce the risk of injury due to the
implosion of the CRT.
mm or more reduce the risk of injury due to the
implosion of the CRT.
N/A
4.3.2
Equipment with handles complies with special loading
tests.
tests.
N/A
5.1.8.3
Equipment intended to receive telecommunication
ringing signals comply with a special touch current
measurement tests.
ringing signals comply with a special touch current
measurement tests.
N/A
5.3.7
Internal (e.g., card cage) SELV circuit connectors and
printed wiring board connectors that are accessible to
the operator and that deliver power are overloaded.
printed wiring board connectors that are accessible to
the operator and that deliver power are overloaded.
N/A
During abnormal operating testing, if a circuit is
interrupted by the opening of a component, the test
shall be repeated twice (three tests total) using new
components as necessary
interrupted by the opening of a component, the test
shall be repeated twice (three tests total) using new
components as necessary
N/A
6.4
Equipment intended for connection to
telecommunication network outside plant cable is
protected against overvoltage from power line crosses
in accordance with 6.4 and Annex NAC.
telecommunication network outside plant cable is
protected against overvoltage from power line crosses
in accordance with 6.4 and Annex NAC.
N/A
Annex EE
Articulated accessibility probe (Fig EE.3) is used for
assessing accessibility to document/media shredders
instead of the Figure 2A test finger.
assessing accessibility to document/media shredders
instead of the Figure 2A test finger.
N/A
M.2
Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions
permitted if the equipment is subjected to special
installation and performance restrictions
N/A
Annex
NAD
NAD
Equipment connected to a telecommunication and
cable distribution networks and supplied with an
earphone intended to be held against, or in the ear
comply with special acoustic pressure requirements
cable distribution networks and supplied with an
earphone intended to be held against, or in the ear
comply with special acoustic pressure requirements
N/A
Click on the first or last page to see other ESQUIRE service manuals if exist.