Read Harman Kardon AVR 45 (serv.man16) User Guide / Operation Manual online
Programming the Remote
34
ENGLISH
Example: To have the AVR’s volume
control be activated even though the
remote is set to control the TV, first press
the
control be activated even though the
remote is set to control the TV, first press
the
TV Device Control Selector
b
, and the
Mute
button
d
at the
same time. Next, press the
Volume Up
button
z
, followed by the
AVR
Device Control Selector
a
.
NOTE: Should you wish to return the
remote to the original configuration after
entering a Volume Punch-Through, you
will need to repeat the steps shown above.
However, press the same Device Control
Selector in steps one and three.
remote to the original configuration after
entering a Volume Punch-Through, you
will need to repeat the steps shown above.
However, press the same Device Control
Selector in steps one and three.
Macro Programming
The Power button may be programmed to
send out a sequence of up to ten com-
mands when it is pushed. This enables you
to turn on a number of products, and have
a program source turn to a favorite
channel or any other command. In
addition, a separate set of macro
command steps may be programmed for
audio devices and video devices.
send out a sequence of up to ten com-
mands when it is pushed. This enables you
to turn on a number of products, and have
a program source turn to a favorite
channel or any other command. In
addition, a separate set of macro
command steps may be programmed for
audio devices and video devices.
Note that only buttons preprogrammed or
manually programmed can be used for
macro programming.
manually programmed can be used for
macro programming.
To program a macro into the Power
button, follow these steps:
button, follow these steps:
1. Press either the
AVR
button
a
to
program one Power macro, or the
SAT
Device Control Selector
b
to
program another Power macro, and the
Mute
button
d
at the same time until
the red light under the
Device
Control Selector
turns on and the
Programming Status LED
lights red.
• When you press the
AVR
button
a
in this step, the macro steps
programmed will play back and
operate in the same fashion when the
Power button is pressed for the AVR,
CD, TAPE or AUX device selectors.
programmed will play back and
operate in the same fashion when the
Power button is pressed for the AVR,
CD, TAPE or AUX device selectors.
• When you press the
SAT Device
Control Selector
b
in this step, the
macro steps programmed will play back
and operate in the same fashion when
the Power button is pressed for the SAT,
TV, VCR or CBL device selectors.
and operate in the same fashion when
the Power button is pressed for the SAT,
TV, VCR or CBL device selectors.
2. Press the
Power
button
c
.
3. Enter up to ten macro steps by pressing the
Device Control Selector
b
for any
Audio or Video device to which you wish to
have the command sent, and then the
function button for each step you wish to
enter. Note that pressing the
have the command sent, and then the
function button for each step you wish to
enter. Note that pressing the
Device
Control Selector
to change devices is
considered one of the ten macro steps
available.
available.
• To enter the “Power On/Off” command
during macro programming, press the
Mute
button
d
. DO NOT press the
actual Power button.
• Note that the
Channel Up/Down
buttons
z `
may NOT be used
during a macro program sequence.
4. When all steps, up to ten, have been
entered, press the
Sleep/Channel Up
button
`
to enter the commands. The
red light under the Device Control
Selector will blink twice and then turn
off.
Selector will blink twice and then turn
off.
Example: To program your TV, Cable Box
and the AVR45RDS to turn on when the
Power button is pressed, first press-and-hold
the
and the AVR45RDS to turn on when the
Power button is pressed, first press-and-hold
the
SAT
b
and
Mute
buttons
d
until
the red light comes on under the
AVR
button and then the
Power
button
c
.
Next, press the
AVR
button
a
to select
the AVR mode and then the
Mute
button
d
to enter the Power command for the
AVR. Press the
TV Device Control
Selector
b
to select the TV mode, and
then press the
Mute
button
d
again, to
select TV Power. Finally, press the
CBL
Device Control Selector
b
followed
by the
Mute
button
d
to select Cable
Power. Press the
Sleep/Channel Up
button
`
to enter the commands.
After following these steps, each time
you press the
you press the
Power
button
c
, after
either the
SAT
,
TV
,
VCR
or
CBL
Device Control Selector
b
has
been pressed, the remote will send all
the “Power On/Off” commands.
the “Power On/Off” commands.
Erasing a Power Button Macro
To remove a macro program, follow steps
1, 2 and 4 above, but do not follow step
three. For example, to erase the macro for
the video devices just entered, press the
To remove a macro program, follow steps
1, 2 and 4 above, but do not follow step
three. For example, to erase the macro for
the video devices just entered, press the
SAT Device Control Selector
b
and the
Mute
button
d
at the same
time until the red light under the
SAT
button turns on. Press the
Power
button
c
, and then press the
Sleep/Channel
Up
button
`
. The red light under the
Device Control Selector
will blink
twice to confirm the data erasing and then
turn off.
turn off.
IMPORTANT NOTE: If the macro
programming was made with the
programming was made with the
AVR
button
a
the
Power
button
c
cannot be used anymore to only turn on/off
the power of any Audio device (AVR, CD,
Tape) even not of the AVR45RDS itself.
Pressing the Power button after any Audio
device was selected by the appropriate
the power of any Audio device (AVR, CD,
Tape) even not of the AVR45RDS itself.
Pressing the Power button after any Audio
device was selected by the appropriate
Device Control Selector
b
will
always play the macro programmed. The
same is with all Video devices (SAT, TV, VCR,
CBL) if the macro was made with the
same is with all Video devices (SAT, TV, VCR,
CBL) if the macro was made with the
SAT
button
b
.
Click on the first or last page to see other AVR 45 (serv.man16) service manuals if exist.