Read Harman Kardon AVR 45 (serv.man16) User Guide / Operation Manual online
Programming the Remote
33
ENGLISH
Erasing All the Learned Commands For a
Single Device
To erase all the commands for a single
device, follow these steps:
Single Device
To erase all the commands for a single
device, follow these steps:
1. Press the
Device Control Selector
b
for the desired device (e.g., CD, TV,
VCR etc.) and the
Set
button
i
at the
same time until the LED under the
Device Control Selector
turns red
and the
Programming Status LED
turns and remains orange.
2. Press and hold the
Light
button
p
.
The
Programming Status LED
will flash red five times, then the red
LED under the
LED under the
Device Control
Selector
b
will turn off and the
Programming Status LED
will
flash green twice, and then turn to a
steady orange color. The red LED under
the
steady orange color. The red LED under
the
Device Control Selector
b
will turn back on.
3. Now release the
Light
button
p
.
4. At this point, all the learned codes for the
device have been erased. To complete the
process, press and hold the
process, press and hold the
Device
Control Selector
b
and the
Light
button
p
at the same time until the
Programming Status LED
flashes orange twice and then goes out,
and the red LED under the
and the red LED under the
Device
Control Selector
turns off.
Erasing All Learned Commands
To erase ALL commands that have been
learned to all buttons in the remote, follow
the instruction shown below. Note that this
will erase all commands for the CD, TAPE,
SAT, TV, VCR, CBL and AUX devices, but it
will not erase the commands for the
AVR45RDS, itself and all preprogrammed
commands for all devices.
To erase ALL commands that have been
learned to all buttons in the remote, follow
the instruction shown below. Note that this
will erase all commands for the CD, TAPE,
SAT, TV, VCR, CBL and AUX devices, but it
will not erase the commands for the
AVR45RDS, itself and all preprogrammed
commands for all devices.
To erase all learned commands, press and
hold the
hold the
TV Device Control Selector
b
and the
Light
button
p
at the same
time until the
Programming Status
LED
flashes red ten times, then green
once and orange once. When the
Programming Status LED
stops
flashing and turns off, all learned
commands have been erased from the
AVR45RDS remote control.
commands have been erased from the
AVR45RDS remote control.
Back Light
The AVR45RDS remote is equipped
with a soft back light that will illuminate
the remote’s buttons so that they will be
more visible in the darkened room
environment common to home theater
settings.
with a soft back light that will illuminate
the remote’s buttons so that they will be
more visible in the darkened room
environment common to home theater
settings.
To illuminate the back light, simply press
the
the
Light
button
p
. The back light will
remain on for eight seconds and then go
out. The light will remain on for an
additional eight seconds each time any
button is pressed on the remote while the
light is already on.
out. The light will remain on for an
additional eight seconds each time any
button is pressed on the remote while the
light is already on.
Note that excessive use of the back light
will shorten battery life.
will shorten battery life.
Volume Punch-Through
The AVR45RDS’s remote may be
programmed to operate the
programmed to operate the
Volume
Control
z
and
Mute
button
d
from
either the TV or the AVR to operate in
conjunction with any of the eight devices
controlled by the remote. For example,
since the AVR45RDS will likely be used as
the sound system for TV viewing, you may
wish to have the AVR’s volume activated
when the remote is set to run the TV. Either
the AVR or TV volume control may be
associated with any of the remote’s devices.
conjunction with any of the eight devices
controlled by the remote. For example,
since the AVR45RDS will likely be used as
the sound system for TV viewing, you may
wish to have the AVR’s volume activated
when the remote is set to run the TV. Either
the AVR or TV volume control may be
associated with any of the remote’s devices.
To program the remote for Volume Punch-
Through, follow these steps:
Through, follow these steps:
1. Press the
Device Control Selector
b
for the device you wish to have
associated with the volume control
(e.g., TV, SAT, etc.) and the
(e.g., TV, SAT, etc.) and the
Mute
button
d
at the same time until the
red light illuminates under the
Device
Control Selector
.
2. Press the
Volume Up
button
z
.
3. Press either the
AVR
a
or the
TV
Device Control Selector
b
,
depending on which system’s volume
control you wish to have attached for
the punch-through mode. Note that the
red light under the
control you wish to have attached for
the punch-through mode. Note that the
red light under the
Device Control
Selector
will blink twice and then go
out to confirm the data entry.
Click on the first or last page to see other AVR 45 (serv.man16) service manuals if exist.