AVR 11 (serv.man5) - Harman Kardon Audio User Guide / Operation Manual. Page 8

Front Panel Controls

2

1 POWER Button: 

Press this button

to turn the power totally on and off
(not remotable, see also page 10).

2 HEADPHONES Jack: Stereo
headphones may be plugged into this
jack for private listening. Headphone
impedance should be between 
8 ohms and 2K ohms. Best results are
between 200 and 400 ohms.

3 BYPASS Selector: Defeats all
surround modes.

4 SURROUND MODE Selector:
Press this button to select the desired
surround mode. The mode is changed
between normal DOLBY Pro-Logic
and DOLBY 3-STEREO.

5 TAPE MONITOR Button: Press
this button to select input from a tape
deck or to monitor a recording in
progress (with 3 head decks).

6 INPUT Selector Buttons: Press
these buttons to select the desired
input source.

7 BASS Control: Modifies the low-
frequency sound of the left and right
channels as much as ±10dB. Set this
control at a suitable position for your
taste and room acoustics.

8 TREBLE Control: Modifies the
high-frequency sound of the left and
right channels as much as ±10 dB. Set
this control at a suitable position for
your taste and room acoustics.

9 BALANCE Control: This control is
used for balancing the relative sound
volume of the left and right channel
speakers. Clockwise rotation reduces
the volume from the left speaker,
counterclockwise rotation reduces the
volume from the right speaker.

) VCR2 A/V INPUT Jacks:
Connect these jacks to the corre-
sponding output jacks of a VCR
(Yellow: Video, Red/White: Audio).

! STATION PRESET Buttons:
These buttons are used to recall or
store preset stations. Pressing the
buttons will automatically choose the
tuner as an input and switch to the
selected station. Pressing the buttons
after pushing MEMORY

@ will store

a station’s frequency to the desired
location.

NOTE: To select or enter a preset
location between 10 and 29 you must
select the second digit within 2
seconds of the first. To select preset
location 30, simply press 0.

@ MEMORY Button: Press this
button to store an AM or FM
frequency in the unit’s memory. 
The MEMORY indicator will blink in the
display to remind you to choose a
location using the STATION 
PRESET

! buttons. Storing a station

in a memory location that has already
been used will overwrite the existing
data.

NOTE: The preset memories are
protected from power loss for two
weeks. If the unit is totally switched off
or unplugged for more than two
weeks, all stored frequencies will be
erased.

# SEEK / STEREO Button: Press
this button, AUTO will illuminate in the
display and the tuner automatically
switches to Mono or Stereo mode
correspondingly to the received signal.
Then press the Tuning/PTY 

¤

or 

⁄

button. The tuner will automatically
seek out stations in your area that
have enough signal strength to be
listenable.

$ DISPLAY WINDOW: 
The indicators in this display provide
information about the input source,
tuner/ RDS operation and surround
options. The IR remote sensor is also
behind this window.

NOTE: For optimal operation of the
remote control be certain that the
window is not blocked by cabinet
doors or other obstructions.

% PTY (Program Type Search):
When the RDS system is engaged by
pressing RDS

^, this button is used

to initiate a search for stations with a
specific Programme Type (PTY). Press
this button and note that PTY SEL
appears in the display window. Use
the TUNING/PTY buttons 

& to scroll

through the list of available PTY types
and press the PTY-button again to
scan for your selection. The display
will indicate the preset number for all
stations with the correct PTY and tune
to the strongest.

AVR11 engelsk manual  11/01/98 10:46  Side 2