AVR 11 (serv.man5) - Harman Kardon Audio User Guide / Operation Manual. Page 11

System Remote Control

5

a INFRARED TRANSMITTER
WINDOW: The infrared beam is
emitted forward from this window
when you press any button on the
commander. For the remote control to
function properly, always point this
window toward the remote sensor
window on the receiver and do not
obstruct this window with any
material.

b STANDBY Button:
Press this button to turn the power on
and off (from and to Standby mode).
In order for this button to function, the
front panel POWER

1 button must

be set to ON. 

If you connect other components to
the switched AC outlet, this Standby
button can also be used as a system
power button.

NOTE: Automatic power on: When
you press the input function buttons
(CD, TUNER, TAPE, TV/AUX, VCR 1,
VCR 2) in STANDBY mode, the power
is automatically turned on and the
input is selected.

c TUNING UP/DOWN:
Press these buttons to tune the tuner
frequency up or down.

d PRESET SCAN Button:
Press this button to scan preset
stations (see page 11).

Remote Control
Operation Range

MHz

MO

KHz

MEM

PRESET

TAPE

1

VCR

AUTO

TUNED

STEREO

3 Stereo

SLEEP

Pro

RDS TA

INFO

NEWS

Logic

dB

e NUMERIC Buttons:
These buttons can be used for preset
tuning in TUNER mode.

Preset tuning: Select one of the 30
preset locations by pressing the
numeric buttons directly, thereby the
input of the receiver automatically is
changed to TUNER.

f CD FUNCTION Buttons:
Use these buttons to control the
transport and disc selection functions
of a compatible Harman Kardon CD
player or CD changer.

g CASSETTE DECK FUNCTION
Buttons: 
Use these buttons to control the
functions of a compatible Harman
Kardon cassette deck.

h DELAY TIME Button:
This button operates only in Dolby Pro
Logic mode. In this mode the output
signal from the surround speakers is
delayed slightly from that of the front
speakers.

Select appropriate delay time to
achieve the best surround sound
effect. For Dolby Surround sound, we
recommend a 20ms delay. The time is
changed as below, when the button is
pressed in succession.

i INPUT FUNCTION Selector:
Press the button to select the desired
input function. The available buttons
are CD, TUNER, TAPE, TV/AUX, VCR
1, and VCR 2.

j CENTER LEVEL UP/DOWN 
Buttons:
Use these buttons to adjust the sound
level of the center speaker to that of
the front speakers. These buttons
work only in Dolby Pro Logic and
Dolby 3 Stereo mode. These buttons
do not work in PHANTOM mode.

15ms

20ms

25ms

30ms

k CENTER MODE Button: 
This button selects the center channel
options for surround modes.

l TEST TONE Button: 
Press this button to turn on the test
signal generator for system setup.

m REAR LEVEL UP/DOWN
Buttons:
These buttons operate only in Dolby
PRO LOGIC mode. Use these buttons
to adjust the sound level of the
surround speakers. Set the MASTER
VOLUME control at the desired level
and then press these buttons until you
get the optimum surround effect at
your listening position.

n MASTER VOLUME Buttons:
Adjust the overall (Front, Center 
and Rear) volume level using these
buttons.

o DISPLAY Button
Press this button to dim the display.
Press it again to turn the display totally
off and once more to return it to
normal.

p SLEEP Button
This button sets the receiver to
automatically turn off after 10, 20, 30,
60 or 90 minutes. Each time the
button is pressed, the setting is
advanced as below.

The display will dim when the sleep
function has been set.

10

min

20

min

30

min

60

min

90

min

OFF

AVR11 engelsk manual  11/01/98 10:46  Side 5