Read Sony KV-28DX30U Service Manual online
11
13
Additional TV Features
Before listening to Dolby Pro Logic encoded programmes, you can adapt the Dolby features to suit your own taste. This is only
required if you have connected your own external speakers (SS-CR190 or equivalent), and/or if you decide to change the speaker
positions.
Note: There will be no output available from the headphones or the audio output sockets on the rear of the TV during Dolby Pro
Logic mode.
required if you have connected your own external speakers (SS-CR190 or equivalent), and/or if you decide to change the speaker
positions.
Note: There will be no output available from the headphones or the audio output sockets on the rear of the TV during Dolby Pro
Logic mode.
Setting up Dolby Pro Logic
1. Press the MENU button on the remote control to display
the menu on the TV screen.
2. Press the
V
or
v
buttons to select the
symbol on the
menu screen then press the
b
button to enter the
‘PRESET’ menu.
3. Press the
V
or
v
buttons to select ‘Dolby Mode Setup’ on
the menu screen then press the
b
button to enter the
‘DOLBY MODE SETUP’ menu.
4. Press the
V
or
v
buttons to select ‘Dolby Mode’, then
press the
b
button to enter. Press the
b
or
B
buttons to
select one of the following modes then press the OK
button to store the chosen mode:
Pro Logic: all 5 speakers are activated
3 stereo: surround speakers are not used
Virtual: no external speakers required. Do not select this
mode if you wish to receive Dolby Pro logic
button to store the chosen mode:
Pro Logic: all 5 speakers are activated
3 stereo: surround speakers are not used
Virtual: no external speakers required. Do not select this
mode if you wish to receive Dolby Pro logic
5. Press the
v
button to select ‘Centre Mode’, then push the
b
button to enter. Press the
b
or
B
buttons to select one
of the following modes then press the OK button to store
the chosen mode:
Normal: all 5 speakers are activated
Wide: wider bandwidth for centre speaker
Phantom: centre speaker is not used (This cannot be
selected if you have chosen “3 stereo” mode in step 4)
the chosen mode:
Normal: all 5 speakers are activated
Wide: wider bandwidth for centre speaker
Phantom: centre speaker is not used (This cannot be
selected if you have chosen “3 stereo” mode in step 4)
6. Press the
v
button to select ‘Test Tone’ then push the
b
button to enter. Press the
b
or
B
buttons to select ‘On’,
then press the OK button.
The test tone will cycle through all the speakers.
The test tone will cycle through all the speakers.
7. Press the
v
button to select the ‘Left Speaker’, then press
the
b
button to confirm. The tone remains at the left
speaker.
8. Press the
V
or
v
buttons to alter the sound level, then
press the OK button.
9. Repeat steps 7 and 8 to select and adjust the ‘Centre’,
‘Right’, and ‘Surround’ speakers, so that the sound output
from all speakers are balanced in relation to your sitting
position.
from all speakers are balanced in relation to your sitting
position.
10. Press the MENU button to remove the display.
Note: After setting up Dolby ProLogic, refer to the ‘Adjusting the sound’ section
on page 11 and set the Surround Mode to Pro Logic.
RM-888
MENU
PROGR
OK
11
RM-888
MENU
PROGR
OK
Additional TV Features
Although the sound is adjusted at the factory, you can modify it to suit your own taste.
Adjusting the sound
1. Press the MENU button on the remote control to display the
menu on the TV screen.
2. Press the
V
or
v
buttons to select the
symbol on the
menu screen then press the
b
button to enter the ‘SOUND
CONTROL’ menu.
3. Press the
V
or
v
buttons to select the item on the screen you
wish to adjust then press the
b
button to confirm. For a
description of the menu items and their effects, see the table
below.
below.
4. If you selected ‘Sound Mode’ or ‘Surround Mode’ in step 3,
press the
V
or
v
buttons to select the item on the screen you
wish to adjust then press the
b
button to confirm.
5. Press the
b
or
B
buttons to adjust your selected item.
6. As soon as you have adjusted the item, press the OK button
to store the new setting.
7. If you selected ‘Sound Mode’ or ‘Surround Mode’ in step 3,
press the
B
button to return to the ‘SOUND CONTROL’
menu.
8. Repeat steps 3-7 to adjust the other items.
9. Press the MENU button to remove the menu from the TV
9. Press the MENU button to remove the menu from the TV
screen.
Sound Mode
b Personal
Rock
Jazz
B Pop
Balance
Reset
Resets sound to factory preset levels
Bass Extension
Boosts bass by a fixed amount
Surround Mode
Choose from the special sound effects:
Off --> Pro Logic --> 3 Stereo --> Virtual Dolby -->
Pseudo Stereo --> Spatial
Off --> Pro Logic --> 3 Stereo --> Virtual Dolby -->
Pseudo Stereo --> Spatial
Dual Sound
Stereo
B
b Mono (for a stereo broadcast)
A for channel 1
B b B for channel 2
(for a bilingual broadcast)
Volume Offset
B The channel volume level can be b
adjusted over a range of -12 to +12.
Headphones
i Volume
i Volume
i Dual Sound
Stereo
B b Mono (for a stereo broadcast)
A for channel 1
B b B for channel 2
(for a bilingual broadcast)
Auto Surround
Set to ‘On’ to automatically select Pro Logic
Surround sound when transmitted.
Surround sound when transmitted.
In ‘Personal’ mode, Treble and Bass can be adjusted
Only available when ‘Surround Mode’ is set to ‘Off’
Click on the first or last page to see other KV-28DX30U service manuals if exist.