Read Sony KP-46WT520 / KP-51WS520 / KP-57WS520 (serv.man2) Service Manual online
KP-46WT520/51WS520/57WS520
KP-46WT520/51WS520/57WS520
34
2-10.ELECTRICAL ADJUSTMENTS BY
REMOTE COMMANDER
All of the circuit adjustments can be made by using the remote
commander (RM-Y916).
commander (RM-Y916).
Note: The following test equipment is required:
1. Pattern Generator (with component outputs)
2. Frequency counter
3. Digital multimeter
4. Audio oscillator
2-10-1. METHOD OF ENTERING THE SERVICE
ADJUSTMENT MODE
SERVICE MODE PROCEDURE
1. TV must be in Standby mode. (Power off)
1. TV must be in Standby mode. (Power off)
2. Press “DISPLAY”, “5”, “VOL +”, then “POWER” on the remote
commander.
(Press each button within 1 second of pressing the previous button.)
SERVICE MODE ADJUSTMENT
Data
WSL : XXX
0 0
3D-COMB
NRMD
NRMD
F / A FLAG : XXXXXXXX
CBA FLAG : XXXXXXXX
CBA FLAG : XXXXXXXX
SERVICE
TV
Item NO.
Adjustment Item
Category
3. The screen displays the item being adjusted within that category.
4. Press 1 or 4 on the remote commander to select the adjustment item
5. Press 3 or 6 on the remote commander to change the data
6. Press 2 or 5 on the remote commander to select the adjustment
category
Every time you press 2 (Category up), service mode changes in the
order shown below:
order shown below:
7. If you want to go back to the most recently saved value, press “0” then
“ENTER” to read the memory.
8. Press “MUTING” then “ENTER” to write the new adjustment data into
memory.
9. Turn power off when you want to exit the service mode.
Note:: Press “8” then “ENTER” on the remote commander to restore the
factory settings for user controls and channel memories (this will also
turn set off and then on to exit the service mode).
turn set off and then on to exit the service mode).
2-10-2. MEMORY WRITE CONFIRMATION
METHOD
1. After adjustment, turn the power off with the remote commander.
2. Turn the power ON and set to service mode.
3. Cycle through the adjusted items again and confi rm that the
adjustments were saved.
2-10-3. ADJUSTING BUTTONS AND
INDICATOR
Note: When the PJE mode (which displays an internally generated
signal) is activated, several buttons on the remote commander will have
different functions than the ones listed below. Therefore, when in the PJE
mode, refer to section 2-12-3 for button functions.
signal) is activated, several buttons on the remote commander will have
different functions than the ones listed below. Therefore, when in the PJE
mode, refer to section 2-12-3 for button functions.
MUTING
Category up
Adjustment
item up
item up
Adjustment
item down
item down
ENTER
Category
down
down
Data down
Data up
DISPLAY
POWER
Test Reset
VOLUME
PICTURE
TV/VIDEO
WIDE MODE
ANT
RM-Y916
USER
LUMA
VERSION
COLR
CLTY
MIDE
CCPM
YCTS
DEF1
DEF2
DEF4
DEF5
DEF3
PJED AIVP
PJED A1SV
DDEV
MCP
COMB
PJED FDIS
PJED V1CM
PJED OTVS
AWID
SNNR
RNR
BNR
OSDP
ASEL
PJED DFHG
PJED CENT
AP
MSMO
PJED VUP
PJED ROGH
PJED PV3P
PJED SFTF
OP
ATSC
ID
PFOP
PFID
VSEL
DRCV
MID1
MID2
MID3
VSW
CRNR
Click on the first or last page to see other KP-46WT520 / KP-51WS520 / KP-57WS520 (serv.man2) service manuals if exist.