Read Sony KDL-W40A11E Service Manual online
– 8 –
AT2X
RM-ED001
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
SECTION 1
GENERAL
3: Connecting an aerial/VCR
1
Connect your aerial to the
socket on the
rear of the TV.
If connecting to an aerial only
Go to step 3.
Go to step 3.
2
Connect your VCR.
1 Connect the socket on the rear of the TV to
the input socket on your VCR with the RF
lead.
lead.
2 Connect the scart socket on your VCR to the
/
2 scart socket on the rear of the TV
with a scart lead.
3
Connect the supplied mains lead to the AC
IN socket on the rear of the TV.
IN socket on the rear of the TV.
Note
Do not connect the mains lead to your mains socket until
all connections are complete.
all connections are complete.
4
Bundle the cable.
1 Run the mains lead through the bundling band
and attach to the right of the rear panel with
the supplied screw.
the supplied screw.
2 Remove the screw to open one side of the
cable cover and run the cables through, then
tighten the screw again.
tighten the screw again.
(SMART LINK)
1
2
3
IN
OUT
Coaxial cable
(supplied)
(supplied)
Scart lead (not supplied)
RF lead
(not supplied)
(not supplied)
2-
1
2-
2
Mains lead
(supplied)
(supplied)
1
VCR
Rear of the TV
3
7: Auto-tuning the TV
After selecting the language and country/region, a
message confirming the TV start auto-tuning appears
on the screen.
You must tune the TV to receive channels (TV
broadcasts). Do the following to search and store all
available channels.
message confirming the TV start auto-tuning appears
on the screen.
You must tune the TV to receive channels (TV
broadcasts). Do the following to search and store all
available channels.
1
Press OK to select “Yes”.
The TV starts searching for all available digital
channels, followed by all available analogue
channels. This may take some time, please be
patient and do not press any buttons on the TV or
remote.
Once all available digital and analogue channels
have been stored, the TV returns to normal
operation, displaying the digital channel stored on
channel number 1. If no digital channels are
found, the analogue channel stored on channel 1 is
displayed.
When a message appears for you to confirm the
aerial connections
No digital or analogue channels are found. Check
all the aerial connections and press OK to start
auto-tuning again.
channels, followed by all available analogue
channels. This may take some time, please be
patient and do not press any buttons on the TV or
remote.
Once all available digital and analogue channels
have been stored, the TV returns to normal
operation, displaying the digital channel stored on
channel number 1. If no digital channels are
found, the analogue channel stored on channel 1 is
displayed.
When a message appears for you to confirm the
aerial connections
No digital or analogue channels are found. Check
all the aerial connections and press OK to start
auto-tuning again.
2
When the Programme Sorting menu
appears on the screen, follow steps 2 to 3
of “Programme Sorting (Analogue mode
only)” (page 32).
appears on the screen, follow steps 2 to 3
of “Programme Sorting (Analogue mode
only)” (page 32).
If you do not change the order in which the
analogue channels are stored on the TV, go to step
3.
analogue channels are stored on the TV, go to step
3.
3
Press MENU to exit.
The TV has now tuned in all the available
channels.
channels.
3
1
m
Digital auto-tune display
m
Analogue auto-tune display
Click on the first or last page to see other KDL-W40A11E service manuals if exist.