Read Sony KDL-40HX850 / KDL-40HX853 / KDL-40HX855 / KDL-46HX850 / KDL-46HX853 / KDL-46HX855 / KDL-55HX850 / KDL-55HX853 / KDL-55HX855 (serv.man2) Service Manual online
KDL-40/46/55HX850,853,855(AEP/UK/IT)
16
SELF DIAGNOSIS FUNCTION
DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY LED will flash a set number of times to
indicate the possible cause of the problem.
indicate the possible cause of the problem.
If there is more than one error, the LED will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen.
If the screen displays a “0”, no error has occurred .
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these
problems occur.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the STANDBY LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these
problems occur.
0.5
0.5
3
DISPLAY OF STANDBY LED FLASH COUNT
SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurrences of failure for
confirmation on the screen:
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurrences of failure for
confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
5
* : Note that this differs from entering the service mode (volume +)
*
DISPLAY
TV POWER
Channel
Volume
STBY LED
Flash time
Service menu Item
name
(Screeen Display)
Diagnostic Item Description
2
MAIN_POWE
Main 12 V failure
DC_ALERT
Main 5.0/3.3/1.2 V failur
AUD_PROT
Audio amp. Protection
HDMI_EQ
HDMI equalizer/switch I2C NACK
TU_DEMOD
Tuner or demodulator I2C NACK
4
LD_ERR
LED driver failure/LED voltage protection
P_ID_ERR
Panel ID EEPROM I2C NACK
HFR_ERR
FRC device I2C NACK
TCON_ERR
FRC device Initialization failure
TCON_ERR
E Micro (PEM) not started
6
BACKLITE
Backlight converter OVP
TEMP_ERR
Over temperature protection
TEMP_ERR
Temp. sensor I2C NACK
8
-
Software Error (Also the main board’s memory or Wi-
Fi module is a suspect)
Fi module is a suspect)
9
-
Not used
10
EMIT_ERR
Transmitter board not connected, protection
(3D models only)
(3D models only)
11
-
Not used
12
-
Not used
3
5
7
Click on the first or last page to see other KDL-40HX850 / KDL-40HX853 / KDL-40HX855 / KDL-46HX850 / KDL-46HX853 / KDL-46HX855 / KDL-55HX850 / KDL-55HX853 / KDL-55HX855 (serv.man2) service manuals if exist.