KD-32DX40AS - Sony TV Service Manual (repair manual). Page 10

5. Highlight and activate one of the options using the 

v and b buttons, then press the V or v buttons to

set the option to On or Off. See the table below for an explanation of each option and their effects.

6. Press the OK button to store the new setting, then repeat step 5 to alter the other options.

7. Press MENU button to return to normal TV operation.

Dolby* Virtual

When set to ‘On’, the TV simulates the effects of Dolby Pro Logic Surround sound.

Note:  If you connect headphones to this TV or if you set the ‘Auto Volume’ option to ‘On’,

‘Dolby Virtual’ will automatically be set to Off.

Auto Volume

When set to ‘On’, the volume level will remain constant even if the broadcast level
should change, i.e. during commercial breaks. 

Note:  This option automatically sets itself to ‘Off’  when ‘Dolby Virtual’ is set to ‘On’.

TV Speakers

Set to ‘Off’ if you wish to connect an external amplifier to the audio output sockets on
the rear of the TV.

•

Highlight ‘Reset’ and press OK only if you wish to return the sound settings to their factory preset levels.

•

When receiving a bilingual broadcast set the ‘Dual Sound’ option to ‘A’ for channel 1 sound, ‘B’ for channel 2
sound or ‘Mono’ if the mono channel is available for selection. When receiving a stereo broadcast the ‘Dual
Sound’ option can be set to Stereo or Mono.

*

This TV has been designed to create a Virtual Dolby Surround sound effect from a ‘Dolby Pro Logic Surround’
broadcast without the need for additional speakers. However, you can connect an external amplifier to this TV if
desired (see ‘Connecting additional equipment’ section of this manual).

*

Manufactured under licence from Dolby Laboratories. ‘Dolby’, ‘Pro Logic’ and the double-D symbol are trademarks
of Dolby Laboratories.

The ‘Sleep Timer’ allows you to select a period of time after which the TV automatically switches itself
into standby mode.

1. Press the MENU button to display the main menu. Use the 

V or v button to highlight the   symbol.

Press the 

b button twice to highlight ‘Off’ in the ‘SleepTimer’ menu.

2. Press the 

V or v buttons to set the amount of time before the TV switches itself into standby.  This

can be in 15 minute intervals up to a maximum of 4 hours.

3. Press the OK button to store.

4. Press the MENU button to return to normal TV operation. One minute before the TV switches into

standby, the time remaining is counted down on screen.

Note:  In analogue mode you can check the time remaining until standby by pressing the 

 button. The time

remaining is displayed in the bottom left corner of the TV screen.  

The ‘Set Up’ menu contains many features that enable you to customise your TV. The following pages
explain all of the features contained in the ‘Set Up’ menu.

The TV automatically tuned in all the available channels when you first installed the TV. Follow these
instructions if you wish to re-install your TV at an alternative location or search for new channels that have
been subsequently launched by broadcasters.

1. With the TV in analogue mode, press the MENU button to display the main menu. Press the 

V or v

button to highlight the 

 symbol, then press the 

b button to enter the ‘Set Up’ menu.

2. Press the 

V or v buttons to highlight ‘Auto Tuning’ then press the b button to confirm. The autotune

prompt display appears on screen.

3. Press the OK button to select ‘Yes’ and begin the autotune procedure.

Whilst tuning is taking place, the search and store display appears on screen. 
When all available signals have been captured and stored, the display is removed and the TV returns
to normal operation.

Notes:  You can cancel the tuning at any time by pressing the MENU button.

You can use this feature to change the order in which the analogue channels are stored on your TV.

1. With the TV in analogue mode, press the MENU button to display the main menu. Press the 

V or v

button to highlight the 

 symbol, then press the 

b button to enter the ‘Set Up’ menu.

2. Press the 

V or v buttons to highlight ‘Programme Sorting’ then press the b button to display the

Programme Sorting menu on screen.

3. Press the 

V or v button to highlight the channel you wish to move to a new position, then press the

OK button.

4. Press the 

V or v button to highlight the new channel number for your channel, then press the OK

button.

5. Repeat steps 3 and 4 to move other channels if required, then press the MENU button to return to

normal TV operation.