Read Sony KD-32DX40AS Service Manual online
- 12 -
Additional Information
29
Specifications
TV System
B/G, DVB-T
Colour System
PAL
NTSC 3.58, 4.43 (only Video In)
NTSC 3.58, 4.43 (only Video In)
Channel Coverage
VHF:0-12, 5A, 9A
UHF : 28 to 69
CATV : S01 to S03, S1 to S41
UHF : 28 to 69
CATV : S01 to S03, S1 to S41
Picture Tube
FD Trinitron WIDE Approx. 82cm (32 inches)
Sound Output
Left/Right:
2x14W (music power)
2x7W (RMS)
2x7W (RMS)
Power Consumption
111W
Dimensions (w x h x d)
Approx. 883 x 567 x 562mm
Weight
Approx. 65kg
Rear Terminals
21-pin Euro connector (CENELEC standard)
including
including
audio/video input, YUV input,
TV audio/video output.
21-pin Euro connector (CENELEC standard)
including
21-pin Euro connector (CENELEC standard)
including
audio/video input, S-video input,
selectable audio/video output.
Audio outputs - phono jacks
Audio outputs - phono jacks
MODEM
Modem connection
1
RF In (Digital)
2
RF In (Analogue)
RF Out
Conditional Access Module (CAM) socket
RF Out
Conditional Access Module (CAM) socket
Concealed Side Terminals
Video input - phono jack
Audio inputs - phono jacks
S video input - 4 pin DIN
Headphones jack - minijack stereo
Audio inputs - phono jacks
S video input - 4 pin DIN
Headphones jack - minijack stereo
Accessories Supplied
RM-933 remote control (1)
RF Loopthrough Cable (1)
IEC designated size AA battery (2)
SCART Adaptor (1)
SCART Lead (1)
RF Loopthrough Cable (1)
IEC designated size AA battery (2)
SCART Adaptor (1)
SCART Lead (1)
1/
2/
s
3
3
s
Design and specifications are subject to change without notice.
Additional Information
30
Troubleshooting
Here are some simple soloutions to problems which may affect the picture and sound.
Problem
Cause
No picture, no sound.
Poor or no picture (screen is dark), but good sound.
No Digital channels after tuning.
No Digital channels after tuning.
Some channels are blank.
Standby indicator flashing.
Good Picture, no sound.
Poor picture quality.
No colour on colour programmes.
Remote control does not function.
No colour on colour programmes.
Remote control does not function.
Distorted picture when changing programmes or selecting
Teletext.
Teletext.
•
Power off.
•
TV in standby.
•
Aerial disconnected.
•
Picture preset level adjustment.
•
No digital transmissions in your area.
•
No digital transmissions from the transmitter you are
currently using.
currently using.
•
Weak signal.
•
Unsuitable aerial.
•
Scrambled/subscription-only channel.
•
Programme used only for data (no picture or sound).
•
Programme not being transmitted.
•
Digital mode Timer Record active (regular flash).
•
Fault (irregular flash).
•
Volume control.
•
TV speakers turned off.
•
Headphones are connected.
•
Wrong external mode selected on an YUV/component
video source.
video source.
•
Colour level setting.
•
Batteries low.
•
Media Selector set to wrong mode for the equipment in use.
•
Inputs from external equipment not switched off.
Cause
Solution
TV in standby.
Aerial disconnected.
Picture level adjustment.
Picture level adjustment.
No Digital transmissions in your area.
No Digital transmissions from the transmitter you are
currently using.
Unsuitable aerial.
currently using.
Unsuitable aerial.
Weak signal.
Scrambled/subscription-only channel.
Programme information without picture or sound.
Programme information without picture or sound.
Fault.
Volume control.
TV speakers turned off.
TV speakers turned off.
Wrong external mode selected.
Colour level setting.
•
Plug in the TV.
•
Press the button on the front of the TV.
•
If the indicator is on press the
button or a numbered
button on the remote control.
•
Check the aerial connection.
•
Select on the TV menu system then adjust the
brightness, picture and colour balance levels.
brightness, picture and colour balance levels.
•
Contact a local installer to find out when digital
transmissions begin in your area.
transmissions begin in your area.
•
Contact a local installer to find out at which transmitter you
should be pointing your aerial.
should be pointing your aerial.
•
Change your aerial to cover the channels used by digital
programmes. (Contact a local installer)
programmes. (Contact a local installer)
•
Ensure aerial is correctly aligned to transmitter.
•
Ensure aerial is plugged directly into the TV (not through
other equipment).
other equipment).
•
Upgrade to a higher gain aerial.
•
Subscribe to pay-per-view broadcaster.
•
See ‘Skipping a programme’ section of this manual.
•
See ‘Programme Sorting’ section of this manual.
•
Do not open the cabinet, refer to qualified personnel.
•
Contact your nearest Sony Service Centre.
•
Press the
+ button on the remote control.
•
Refer to ‘The Sound menu’ section in this manual
•
If is displayed on the screen, press the button on the
remote control.
remote control.
•
Disconnect headphones.
•
Press the
button repeatedly until the YUV/component
symbol
is displayed on screen.
•
Select on the TV menu system then adjust the colour
setting.
setting.
/
•
If you continue to have these problems, have your TV serviced by qualified personnel.
•
NEVER open the casing yourself.
Click on the first or last page to see other KD-32DX40AS service manuals if exist.