Read Sony KD-28DL10U Service Manual online
- 12 -
Connecting other
equipment to the TV
equipment to the TV
A wide range of equipment can be connected to the TV through the front and rear
sockets. Most equipment can be connected to any of the TV sockets. Refer to the
instruction manual supplied with your equipment to determine the best TV socket
to use. This TV supports the following inputs:
sockets. Most equipment can be connected to any of the TV sockets. Refer to the
instruction manual supplied with your equipment to determine the best TV socket
to use. This TV supports the following inputs:
Viewing pictures from
a connected VCR
a connected VCR
If you have used a fully wired 21-pin scart lead to connect the VCR:
Refer to ‘Viewing pictures from equipment connected to the rear sockets’, below.
Refer to ‘Viewing pictures from equipment connected to the rear sockets’, below.
If you have not used a fully wired 21-pin scart lead to connect the VCR:
You will need to find the video channel:
You will need to find the video channel:
Viewing pictures from
equipment connected
to the rear sockets
equipment connected
to the rear sockets
Viewing pictures from
equipment connected
to the front sockets
equipment connected
to the front sockets
TV Sockets
Socket type(s)
Inputs supported
i
1/
Scart
RGB, Audio/Video.
i
2/
r
Scart
S-Video, Audio/Video, Smartlink*.
o
3 and
t
3
Phono (x3)
Audio/Video.
(audio via
(audio via
o
3 sockets, video via
t
3 socket)
1.
Insert a pre-recorded tape into the VCR and press the ‘PLAY’ button.
2.
If you inserted a pre-recorded tape and pressed ‘PLAY’ during the
autotune process, as instructed on page 6:
autotune process, as instructed on page 6:
With the TV in analogue mode, press the PROG +/- buttons until the
picture from the pre-recorded tape is displayed on the TV screen.
picture from the pre-recorded tape is displayed on the TV screen.
In future, with the TV in analogue mode, press the Numbered buttons to
directly select the video channel.
directly select the video channel.
If you wish to move your video channel, refer to the ‘Programme Sorting’
on page page 23.
on page page 23.
If you did not insert a pre-recorded tape and press ‘PLAY’ during the
autotune process, as instructed on page 6:
autotune process, as instructed on page 6:
You will need to manually tune in the VCR signal (ideally to channel 0).
Insert a pre-recorded tape into the VCR and press the ‘PLAY’ button.
Refer to the ‘Manual Programme Preset menu’ section of this instruction
manual to manually tune in the VCR signal.
Refer to the ‘Manual Programme Preset menu’ section of this instruction
manual to manually tune in the VCR signal.
After manually tuning the VCR signal and with the TV in analogue mode,
press the Numbered buttons to directly select the video channel.
press the Numbered buttons to directly select the video channel.
1.
Switch on/press ‘PLAY’ on the connected equipment. The picture (if any)
from the equipment appears on the TV screen.
from the equipment appears on the TV screen.
If the picture does not automatically appear press the
/
button
repeatedly until the picture is displayed on the TV screen.
2.
Press the DIGITAL/
a
button to return to normal TV operation.
1.
Press the
/
button repeatedly until the
t
3 symbol appears on the
TV screen.
2.
Switch on/press ‘PLAY’ on the connected equipment. The picture (if any)
from the equipment appears on the TV screen.
from the equipment appears on the TV screen.
3.
Press the DIGITAL/
a
button to return to normal TV operation.
*Smartlink is a direct link between the TV and a
compatible VCR or DVD recorder. Ensure that
your VCR/DVD recorder is connected to the
scart socket labelled
compatible VCR or DVD recorder. Ensure that
your VCR/DVD recorder is connected to the
scart socket labelled
i
2/
r
, using a fully wired
21 pin scart lead. For more information on
Smartlink, refer to the instruction manual
supplied with your Smartlink VCR/DVD recorder.
Smartlink, refer to the instruction manual
supplied with your Smartlink VCR/DVD recorder.
Remote control of
other equipment
other equipment
The remote control supplied with your TV automatically operates the basic
functions of Sony DVD players and most Sony VCRs. The remote control can also
operate DVD players and VCRs made by other manufacturers, provided that it is
first programmed to match the particular brand of your VCR or DVD player**.
functions of Sony DVD players and most Sony VCRs. The remote control can also
operate DVD players and VCRs made by other manufacturers, provided that it is
first programmed to match the particular brand of your VCR or DVD player**.
Programming the remote control
1.
Find the three digit code for your brand from the list below.
2.
If programming the remote control to operate a DVD player:
Press the Mode Selector button repeatedly until the green DVD light
illuminates.
Press the Mode Selector button repeatedly until the green DVD light
illuminates.
If programming the remote control to operate a VCR:
Press the Mode Selector button repeatedly until the green VCR light
illuminates.
Press the Mode Selector button repeatedly until the green VCR light
illuminates.
3.
With the green light illuminated, press and hold down the YELLOW
button for approximately six seconds, until the light starts to flash.
button for approximately six seconds, until the light starts to flash.
4.
Use the Numbered buttons to enter the three digit code for your brand.
Once a correct code has been entered, the green VCR, TV and DVD
lights illuminate together momentarily.
Once a correct code has been entered, the green VCR, TV and DVD
lights illuminate together momentarily.
5.
Turn on your VCR or DVD player and check that the remote control
operates the basic functions (refer to ‘Controlling a DVD player’,
‘Controlling a VCR’ on the next page for details). If not, repeat steps 2-4
and enter the next three digit number for your brand.
operates the basic functions (refer to ‘Controlling a DVD player’,
‘Controlling a VCR’ on the next page for details). If not, repeat steps 2-4
and enter the next three digit number for your brand.
6.
Press the Mode Selector button repeatedly until the green TV light
illuminates.
illuminates.
DVD Brand List
VCR Brand List
Brand
Code
Brand
Code
SONY
001
SONY (VHS)
301, 302,
303, 308, 309
AIWA
021
SONY (BETA)
303, 307, 310
DENON
018, 027, 020, 002
SONY (DV)
304, 305, 306
GRUNDIG
009, 028, 023,
024, 016, 003
AIWA
325, 331, 351
HITACHI
025, 026, 015, 004
AKAI
326, 329, 330
JVC
006, 017
DAEWOO
342, 343
KENWOOD
008
GRUNDIG
358, 355, 360
361, 320, 351
361, 320, 351
LG
015, 014
HITACHI
327, 333, 334
LOEWE
009, 028, 023,
024, 016, 003
JVC
314, 315, 322,
344, 352, 353,
344, 352, 353,
354, 348, 349
MATSUI
013, 016
LG
332, 338
ONKYO
022
LOEWE
358, 355, 360
361, 320, 351
361, 320, 351
PANASONIC
018, 027, 020, 002
MATSUI
356, 357
PHILIPS
009, 028, 023,
024, 016, 003
ORION
328
PIONEER
004
PANASONIC
321, 323
SAMSUNG
011, 014
PHILIPS
311, 312, 313, 316,
317, 318, 358, 359
SANYO
007
SAMSUNG
339, 340, 341, 345
SHARP
019, 027
SANYO
335, 336
THOMSON
012
SHARP
324
TOSHIBA
003
THOMSON
319, 350
YAMAHA
018, 027, 020, 002
TOSHIBA
337
VIDEO
/
TV
/
DIGITAL
Numbered
buttons
buttons
Mode
Selector
button
Selector
button
YELLOW
button
button
*The brand codes you set may be lost if weak
batteries are not replaced immediately. Should
this happen, replace the batteries and re-enter
the required codes. A small label has been
attached to the battery holder for you to make a
note of your brand codes.
batteries are not replaced immediately. Should
this happen, replace the batteries and re-enter
the required codes. A small label has been
attached to the battery holder for you to make a
note of your brand codes.
continued on next page
.
Click on the first or last page to see other KD-28DL10U service manuals if exist.