Read Sony IFU-HS1 / RM-PJHS1 / SU-HS1 / VPL-HS1 / VPL-HS1FP Service Manual online
1-6
VPL-HS1
GB
10
Step 3: Adjusting the Picture Size and Position
Connections and
Preparations
1
Plug the AC power cord into a
wall outlet.
wall outlet.
The ON/STANDBY indicator lights in red and
the projector goes into standby mode.
the projector goes into standby mode.
2
Press the
@
/
1
(on/standby)
switch to turn on the projector.
The ON/STANDBY indicator lights in green.
3
Turn on the equipment
connected to the projector.
connected to the projector.
Refer to the operating instructions of the
connected equipment.
connected equipment.
4
Press INPUT to project the
picture on the screen.
picture on the screen.
Each time you press the button, the input
indication changes. (1 page 15)
indication changes. (1 page 15)
5
Adjust the focus roughly using
the focus lever.
the focus lever.
6
Adjust the size and position of
the picture to fit the screen
using the zoom lever and
adjuster.
the picture to fit the screen
using the zoom lever and
adjuster.
Move the zoom lever to adjust the picture size.
Use the adjuster to adjust the picture position.
Hold down and slide the adjuster stopper to the
right, move the projector, then replace the
stopper.
Hold down and slide the adjuster stopper to the
right, move the projector, then replace the
stopper.
You can move the projector vertically and
horizontally within the following ranges:
horizontally within the following ranges:
ON/
STANDBY
Lights in red.
ON/
STANDBY
Lights in green.
INPUT
VIDEO 1
Focus lever
Zoom lever
Adjuster stopper
Up to 20
°
each for horizontal angle
Up to 10
°
each for
vertical angle
Up to 2
°
each for
tilting angle
11
GB
Step 3: Adjusting the Picture Size and Position
Connections and
Preparations
7
Adjust to correct the
trapezoidal distortion.
trapezoidal distortion.
When projecting from the side
Corrects the horizontal distortion.
Press SIDE SHOT + or – so that the top edge of
the picture becomes parallel to the bottom edge.
If the left side is longer than the right side, press
SIDE SHOT –.
Press SIDE SHOT + or – so that the top edge of
the picture becomes parallel to the bottom edge.
If the left side is longer than the right side, press
SIDE SHOT –.
Use SIDE SHOT + if the right side is longer.
To fine-adjust the distortion, press M or m.
To fine-adjust the distortion, press M or m.
When projecting from the center
Corrects the vertical distortion.
Use the menu. Select V (vertical) with the
KEYSTONE DIR setting in the INSTALL
SETTING
Use the menu. Select V (vertical) with the
KEYSTONE DIR setting in the INSTALL
SETTING
menu. Next, adjust with the
DIGIT KEYSTONE setting so that the left side
of the picture becomes parallel to the right side.
(1 page 20)
If the top edge of the picture is longer than the
bottom edge, set to a plus value.
of the picture becomes parallel to the right side.
(1 page 20)
If the top edge of the picture is longer than the
bottom edge, set to a plus value.
If the bottom edge is longer than the top edge,
set to a minus value.
set to a minus value.
8
Adjust the focus again using
the focus lever.
the focus lever.
Picture
When projecting from
the center
the center
When projecting from
the side
the side
Screen
If you position the projector
below the bottom of the
screen, adjust so that the
bottom edge of the picture
fits the bottom edge of the
screen. For the projector
positioned above the
bottom of the screen,
adjust so that the top edge
of the picture fits the top
edge of the screen.
below the bottom of the
screen, adjust so that the
bottom edge of the picture
fits the bottom edge of the
screen. For the projector
positioned above the
bottom of the screen,
adjust so that the top edge
of the picture fits the top
edge of the screen.
If you position the
projector on the left side
of the screen, adjust so
that the left side of the
picture fits the left side
of the screen. For the
projector positioned on
the right side, adjust so
that the right side of the
picture fits the right side
of the screen.
projector on the left side
of the screen, adjust so
that the left side of the
picture fits the left side
of the screen. For the
projector positioned on
the right side, adjust so
that the right side of the
picture fits the right side
of the screen.
Picture
Screen
Click on the first or last page to see other IFU-HS1 / RM-PJHS1 / SU-HS1 / VPL-HS1 / VPL-HS1FP service manuals if exist.