Read Sony HDR-CX570E / HDR-CX580E / HDR-CX580V / HDR-CX580VE / HDR-CX590V / HDR-PJ580 / HDR-PJ580E / HDR-PJ580V / HDR-PJ580VE / HDR-PJ590V / HDR-PJ600 / HDR-PJ600E / HDR-PJ600V / HDR-PJ600VE (serv.man2) Service Manual online
1-4
HDR-CX570E/CX580E/CX580V/CX580VE/CX590V/PJ580/PJ580E/PJ580V/PJ580VE/PJ590V/PJ600E/PJ600V/PJ600VE_L2
1-6.
SELF-DIAGNOSIS FUNCTION
1-6
-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to do.
This function consists of two display; self-diagnosis display and service
mode display.Details of the self-diagnosis functions are provided in the
Instruction manual.
function starts working, and displays on the LCD screen what to do.
This function consists of two display; self-diagnosis display and service
mode display.Details of the self-diagnosis functions are provided in the
Instruction manual.
1-6
-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the LCD
screen shows a 4-digit display consisting of an alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”of the
problem.
screen shows a 4-digit display consisting of an alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”of the
problem.
0 0
3 2
C
Repaired by:
Refer to “1-6-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32 ....Turn on power again.
13 ....
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
Format the “memory card”.
LCD screen
1-6
-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
0
4
0
0
Non-standard battery is used.
Use the InfoLITHIUM battery.
C
0
6
0
0
The battery pack temperature is high.
Change the battery pack or place it in a cool place.
C
1
3
0
1
Memory card is unformatted.
Memory card is broken.
Memory card is broken.
Format the memory card.
Insert a new memory card.
Insert a new memory card.
C
1
3
0
2
Access error
Remove the power source. Reconnect it again and operate your cam-
corder again.
corder again.
C
1
3
0
3
Access error (External mdedia)
Turn power off and turn power on again.
C
1
3
0
4
Drive fault (External mdedia)
Turn power off and turn power on again.
C
E
3
2
6
1
6
0
0
0
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
Retry turn the power on by the power switch. If it does not recover,
check the focus MR sensor of lens block (pin r;, ra of CN4001 on the
LD-279 board). If it is OK, check the focus motor drive IC (IC1301 on
the VC-653 board).
check the focus MR sensor of lens block (pin r;, ra of CN4001 on the
LD-279 board). If it is OK, check the focus motor drive IC (IC1301 on
the VC-653 board).
E
2
0
0
0
Flash memory data are rewritten.
Make flash memory data correct value. (Note 1)
E
3
1
0
0
Drive fault
Turn power off and turn power on again.
Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATON DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.
Note 2: Functions of codes with * mark are not provided in this unit.
– ENGLISH –
*
*
*
( )
*
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.01
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
Inspect the lens block zoom sensor signal (pin wd of CN4001, pin rk
of CN4005 on the LD-279 board or pin rk of CN1007 on the VC-653
board) when zooming is performed when the zoom lever is operated,
and the zoom motor drive circuit (IC5201 on the LD-279 board) when
zooming is not performed.
E
6
1
1
1
The abnormalities in initialization of the focus
lens and the abnormalities in initialization of
the zoom lens occurred simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
E
6
1
3
0
Reset position detection error on the stepper
iris initializing
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens
drive block (CN4001 pin rf to t; on LD-279 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
･ Case of the iris blades do not close normally Replace the lens block).
･ Case of “E: 61: 30” is appeared and iris blades closed completely.
･ Case of the iris blades do not close normally Replace the lens block).
･ Case of “E: 61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
･ Case of LCD is not displayed normally Check that connection be-
･ Case of LCD is not displayed normally Check that connection be-
tween CN6702 on CM-123 board and CN1004 on VC-653 board
by FP-1488 flexible board.
･ Case of LCD is displayed normally Replace the lens block.
E
6
2
0
0
Handshake correction function does not work
well. (With PITCH angular velocity sensor
output stopped.)
Inspect PITCH angular velocity sensors (SE7501 on the MS-478
board) peripheral circuits.
E
6
2
0
1
Handshake correction function does not work
well. (With YAW angular velocity sensor
output stopped.)
Inspect YAW angular velocity sensors (SE7501 on the MS-478 board)
peripheral circuits.
E
6
2
0
2
Abnormality of IC for steadyshot.
Refer to [
1-7
-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Oc-
curred].
E
6
2
0
3
IC for steadyshot and micro controller com-
munication abnormality among.
Inspect the steadyshot circuit (IC5501 on the LD-279 board).
E
6
2
0
4
Image vibration correction during
handshake function does not work.
Inspect the image vibration angular velocity sensors (SE7701 on the
LD-279 board) peripheral circuits.
E
6
2
1
0
Shift lens initializing failure.
Replacement of lens block (Note 3).
If an error occurs again, replace the LD-279 board.
E
6
2
1
1
Shift lens overheating (Pitch)
Refer to [
1-7
-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred].
E
6
2
1
2
Shift lens overheating (Yaw)
Refer to [
1-7
-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred].
E
6
2
2
0
Abnormality of thermistor.
Refer to [
1-7
-4. E : 62 : 20 (Abnormality of Thermistor) Occurred].
E
9
1
0
1
Abnormality when flash is beingcharged.
Check or replace the LED Flash/Video light or charging capacitor.
E
9
1
0
2
Abnormality of LED Video light.
Check or replace the LED Flash/Video light or charging capacitor.
E
9
1
0
3
Abnormality of LED Video light Tempera-
ture detection.
Check or replace the LED Flash/Video light or charging capacitor.
E
9
2
0
1
Battery current value goes over the max
discharge current
Check the remaining battery power because this symptom maybe
depended on the remaining battery level, and confirm whether or
not the symptom is occurred after replacing the battery. If the symp-
tom is still occurred, overhaul inspection is needed. Check each
output of DC/DC converter (IC4301 on the VC-653 board) with
connected the DC JACK (J901) on the VC-653 board.
(The minimum connection to periphery)
E
9
4
0
0
Fault of writing or erasing the flash mem-
ory
CX580E/CX580V/CX580VE/PJ580/PJ580E/PJ580V/PJ580VE:
Inspect the flash memory (IC8101 on the LD-279 board).
CX590V/PJ590V:
Inspect the flash memory (IC8101, IC8201 on the LD-279 board).
Click on the first or last page to see other HDR-CX570E / HDR-CX580E / HDR-CX580V / HDR-CX580VE / HDR-CX590V / HDR-PJ580 / HDR-PJ580E / HDR-PJ580V / HDR-PJ580VE / HDR-PJ590V / HDR-PJ600 / HDR-PJ600E / HDR-PJ600V / HDR-PJ600VE (serv.man2) service manuals if exist.