Read Sony HDR-CX300 / HDR-CX300E / HDR-CX305E / HDR-CX350 / HDR-CX350E / HDR-CX350V / HDR-CX350VE / HDR-CX370 / HDR-CX370E / HDR-CX370V / HDR-XR350 / HDR-XR350E / HDR-XR350V (serv.man2) Service Manual online
1-2
HDR-CX300/CX300E/CX305E/CX350/CX350E/CX350V/CX350VE/CX370/CX370E/CX370V/XR350/XR350E/XR350V/XR350VE_L2
– ENGLISH –
1-5. METHOD OF COPING WITH SHIFT LENS ERROR
IC7501
VC-588 BOARD (SIDE B)
VC-588 BOARD (SIDE A)
R5653
IC5501
R5524
R5527
Fig. 1
Measurement points on the VC-588 board
about 330 msec
Note: The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R5653 on the VC-588 board
1-5-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5653 in the periphery of IC5501 on the VC-588 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC7501 of VC-588 board) periphery.
the camera control circuit (IC7501 of VC-588 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
E
6
1
1
1
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis
code.
code.
E
6
2
0
0
Handshake correction function does not
work well. (With PITCH angular velocity
sensor output stopped.)
work well. (With PITCH angular velocity
sensor output stopped.)
Inspect PITCH angular velocity sensors (SE6602 on the MS-
430 board) peripheral circuits.
430 board) peripheral circuits.
E
6
2
0
1
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Inspect YAW angular velocity sensors (SE6601 on the MS-430
board) peripheral circuits.
board) peripheral circuits.
E
6
2
0
2
Abnormality of IC for steadyshot.
Refer to [1-5-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
Occurred].
Occurred].
E
6
2
0
3
IC for steadyshot and micro controller
communication abnormality among.
communication abnormality among.
Inspect the steadyshot circuit (IC5501 on the VC-588 board).
E
6
2
0
4
Image vibration correction during
handshake function does not work.
handshake function does not work.
Inspect the image vibration angular velocity sensors
(SE9101 on the JK-394/JK-397 board) peripheral circuits.
(SE9101 on the JK-394/JK-397 board) peripheral circuits.
E
6
2
1
0
Shift lens initializing failure.
Replacement of lens block. (Note2) If an error occurs again,
replace the VC-588 board.
replace the VC-588 board.
E
6
2
1
1
Shift lens overheating (Pitch)
Refer to [1-5-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
Occurred].
Occurred].
E
6
2
1
2
Shift lens overheating (Yaw)
Refer to [1-5-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
Occurred].
Occurred].
E
6
2
2
0
Abnormality of thermistor.
Refer to [1-5-4. E : 62 : 20 (Abnormality of Thermistor) Oc-
curred].
curred].
E
9
1
0
1
Abnormality when flash is being
charged.
charged.
Checking of flash unit or replacement of flash unit.
E
9
2
0
1
Battery current value goes over the max
discharge current
discharge current
Check the remaining battery power because this symptom
maybe depended on the remaining battery level, and confirm
whether or not the symptom is occurred after replacing the
battery. If the symptom is still occurred, overhaul inspection
is needed. Check each output of DC/DC converter (IC4701)
on VC-588 board with connected the
maybe depended on the remaining battery level, and confirm
whether or not the symptom is occurred after replacing the
battery. If the symptom is still occurred, overhaul inspection
is needed. Check each output of DC/DC converter (IC4701)
on VC-588 board with connected the
DC JACK (J901,
BT901)
(the minimum connection to periphery) to VC-588
board.
E
9
4
0
0
Fault of writing or erasing the flash
memory
memory
Inspect the flash memory (IC8101 on the VC-588 board).
E
9
4
0
1
Internal flash memory fault
Inspect the flash memory (IC8101 on the VC-588 board).
E
9
4
0
2
BGM data error
Inspect the flash memory (IC8101 on the VC-588 board). If
it is OK, check the CPU (IC7501 on the VC-588 board).
it is OK, check the CPU (IC7501 on the VC-588 board).
E
9
5
0
0
GPS hardware error
CX350V/CX350VE/CX370V/XR350V/XR350VE:
Check whether the
Check whether the
FP-1021 flexible board
is broken,and
check whether it is inserted imperfectly. If there is no prob-
lem the flexible board, inspect or replacement of the
lem the flexible board, inspect or replacement of the
GPS
module (GP342 ASSY)
.
E
9
6
0
0
Map area mount error
CX350V/CX350VE/CX370V/XR350V/XR350VE:
Inspect or replacement of the MM-088 board (CX350V/CX-
350VE/CX370V), hard disk unit (XR350V/XR350VE).
Inspect or replacement of the MM-088 board (CX350V/CX-
350VE/CX370V), hard disk unit (XR350V/XR350VE).
Note2: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.02
Click on the first or last page to see other HDR-CX300 / HDR-CX300E / HDR-CX305E / HDR-CX350 / HDR-CX350E / HDR-CX350V / HDR-CX350VE / HDR-CX370 / HDR-CX370E / HDR-CX370V / HDR-XR350 / HDR-XR350E / HDR-XR350V (serv.man2) service manuals if exist.