HDR-CX240, HDR-CX240E, HDR-PJ240, HDR-PJ240E, HDR-PJ270, HDR-PJ270E, HDR-PJ275 (serv.man2) - Sony Movie Service Manual (repair manual). Page 6

1-3

HDR-CX240/CX240E/PJ240/PJ240E/PJ270/PJ270E/PJ275_L2

Note 2: Functions of codes with * mark are not provided in this unit.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

6

1

1

1

The abnormalities in initialization of 
the focus lens and the abnormalities in 
initialization of the zoom lens occurred 
simultaneously.

Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.

E

6

1

3

0

Reset position detection error on the 
stepper iris initializing

Turn the power on to open lens barrier. Disconnect the battery or power 
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive 
block (pin wg, wh of CN4002 on theVC-1023 board).
If iris blades work normally, confirm that they are closing completely 
and confirm following item.
•  Case of the iris blades do not close normally. Replace the lens block.
•  Case of “E: 61: 30” is appeared and iris blades closed completely.
  Confirm that communication with lens block is normal.
•  Case of LCD is not displayed normally. Check that connection between 

CN6702 on CM-1004 board and CN4004 on VC-1023 board by FP-
2190 flexible board.

•  Case of LCD is displayed normally. Replace the lens block.

E

6

2

0

0

Handshake correction function does not 
work well. (With PITCH angular veloc-
ity sensor output stopped.)

E:62:00
Inspect PITCH angular velocity sensors (SE7701 on the GY-1005 
board) peripheral circuits.
E:62:01
Inspect YAW angular velocity sensors (SE7701 on the GY-1005 board) 
peripheral circuits.

E

6

2

0

1

Handshake correction function does not 
work well. (With YAW angular velocity 
sensor output stopped.)

E:62:00
Inspect PITCH angular velocity sensors (SE7701 on the GY-1005 
board) peripheral circuits.
E:62:01
Inspect YAW angular velocity sensors (SE7701 on the GY-1005 board) 
peripheral circuits.

E

6

2

0

2

Abnormality of IC for steadyshot.

Turn power off and turn power on again.

E

6

2

0

3

IC for steadyshot and micro controller 
communication abnormality among.

Inspect the steadyshot circuit (IC6800 on the VC-1023 board).

E

6

2

0

4

Image vibration correction during hand-
shake function does not work.

Inspect the image vibration angular velocity sensors (SE7711 on the 
VC-1023 board) peripheral circuits.

E

6

2

1

0

Shift lens initializing failure.

Turn power off and turn power on again.

E

6

2

1

1

Shift lens overheating (Pitch)

Turn power off and turn power on again.

E

6

2

1

2

Shift lens overheating (Yaw)

Turn power off and turn power on again.

E

6

2

2

0

Abnormality of thermistor.

Turn power off and turn power on again.

E

6

2

3

0

Abnormal CPU

Turn power off and turn power on again.

E

9

1

0

1

Abnormality when flash is being 
charged.

Turn power off and turn power on again.

E

9

1

0

2

Abnormality of LED Video light.

Turn power off and turn power on again.

E

9

1

0

3

Abnormality of LED Video light Tem-
perature detection.

Turn power off and turn power on again.

E

9

2

0

1

Battery current value goes over the max 
discharge current

Check the remaining battery power because this symptom maybe de-
pended on the remaining battery level, and confirm whether or not the 
symptom is occurred after replacing the battery. If the symptom is still 
occurred, replace the VC-1023 board.

E

9

4

0

0

Fault of writing or erasing the flash 
memory

PJ270/PJ270E/PJ275:
Inspect the flash memory (IC8101 on the MM-102 board).

E

9

4

0

1

Internal flash memory fault

PJ270/PJ270E/PJ275:
Inspect the flash memory (IC8101 on the MM-102 board).

*
*
*

*

*

*

Refer to the following flowchart when repairing or inspecting the projector’s projection function.

If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart. 
When a defective part has been clarified, repair the projector according to the check result.

Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
 

When replacing a part of the projector unit, wait until it is cooled down.

 

Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.

Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
 

Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.

Indicated defective

projector received

Measure brightness.

(  2)

Yes

No

OK

OK

NG

NG

OK

NG

A

B

Indication on 

brightness

Inspect projector

LED. 

(  1)

  1  Refer to the ADJUST tab of Adjust Manual.
  2  Refer to the SERVICE tab of Adjust Manual.

Inspect projector

LED. 

(  1)

END

-
-
-

-

-

Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)

Projector Data Input

Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40

Syywwnnnnn 

Enter the red part.

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

E

9

4

0

2

BGM data error

Check the CPU (IC6000 on the VC-1023 board).

E

9

5

0

0

GPS hardware error

Turn power off and turn power on again.

E

9

6

0

0

Map area mount error

Turn power off and turn power on again.

E

9

7

0

0

Projector hardware error

Turn power off and turn power on again.

*
*

Note 2: Functions of codes with * mark are not provided in this unit.