Read Sony DCR-VX2200E (serv.man2) Service Manual online
6-11
DCR-VX2200E_ADJ
Order Page Address Data
Procedure
Check the data changes to
8
3
90
“1C”.
9
Perform “Modification of 8,
9, C, 13, 18, 1C, 1D, 1E Page
Data”
9, C, 13, 18, 1C, 1D, 1E Page
Data”
Note 3:
If other than adjustment address was initialized, the ad-
justed data is not initialized.
justed data is not initialized.
2.
Modification of 8, 9, C, 13, 18, 1C, 1D, 1E Page Data
If the 8, 9, C, 13, 18, 1C, 1D, 1E page data has been initialized,
change the data of the “Fixed data-2” address shown in the fol-
lowing table by manual input.
change the data of the “Fixed data-2” address shown in the fol-
lowing table by manual input.
Processing before Modification 8, 9, C, 13, 18, 1C, 1D, 1E
page data:
page data:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
3
71
01
Press PAUSE (Write) button.
Modifying Method:
1) If modification of data on pages 8, 9, C, set data: 00 to page: 0,
1) If modification of data on pages 8, 9, C, set data: 00 to page: 0,
address: 10, and then select pages 8, 9, C.
2) If modification of data on pages 13, 18, 1C, 1D, 1E, set data:
01 to page: 0, address: 10, and then select pages 3, 8, C, D, E.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
3) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note:
If copy the data built in the different model, the cam-
corder may not operate.
corder may not operate.
4) When changing the data, press the PAUSE (Write) button of
the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
data to write the data in the non-volatile memory.
5) If all areas were initialized, check that the data at the addresses
for adjustment are initial values (adjustment initial values)
listed in the table.
If different, change them to the adjustment initial values.
listed in the table.
If different, change them to the adjustment initial values.
Processing after Completing Modification 8, 9, C, 13, 18, 1C,
1D, 1E page data:
1D, 1E page data:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
3
70
10
Press PAUSE (Write) button.
4
3
70
Check the data changes to
“11”.
“11”.
5
2
00
29
6
2
01
29
Press PAUSE (Write) button.
1-2-2.
Initialization of 8, 9, C, 13, 18, 1C, 1D, 1E
Page Data
Page Data
1.
Initializing of 8, 9, C, 13, 18, 1C, 1D, 1E Page Data
Note 1:
If “Initialization of Pages 8, 9, C, 13, 18, 1C, 1D, 1E” is
executed, all data on pages 8, 9, C, 13, 18, 1C, 1D, 1E
are initialized. (Only an individual page cannot be ini-
tialized)
executed, all data on pages 8, 9, C, 13, 18, 1C, 1D, 1E
are initialized. (Only an individual page cannot be ini-
tialized)
Note 2:
If the 8, 9, C, 13, 18, 1C, 1D, 1E page data has been
initialized, the following adjustments need to be per-
formed again.
1) Modification of 8, 9, C, 13, 18, 1C, 1D, 1E page data
2) Electronic viewfinder system adjustments (if all ar-
initialized, the following adjustments need to be per-
formed again.
1) Modification of 8, 9, C, 13, 18, 1C, 1D, 1E page data
2) Electronic viewfinder system adjustments (if all ar-
eas were initialized)
3) LCD system adjustments (if all areas were initial-
ized)
4) Node unique ID No. input (if all areas were initial-
ized)
5) Servo, RF system adjustments (if all areas were ini-
tialized)
6) Video system adjustments (if all areas were initial-
ized)
Adjustment Page
8
Adjustment Address
00 to FF
Adjustment Page
9
Adjustment Address
00 to FF
Adjustment Page
C
Adjustment Address
10 to FF
Adjustment Page
13
Adjustment Address
00 to FF
Adjustment Page
18
Adjustment Address
00 to FF
Adjustment Page
1C
Adjustment Address
00 to FF
Adjustment Page
1D
Adjustment Address
00 to FF
Adjustment Page
1E
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
3
81
Set the following data. (Note
3)
3)
00: Initializing all areas
01: Initializing other than
01: Initializing other than
adjustment address
4
3
80
0C
Press PAUSE (Write) button.
Check the data changes to
5
3
80
“1C”.
Set the following data. (Note
3)
3)
6
3
91
09: Initializing all areas
19: Initializing other than
19: Initializing other than
adjustment address
7
3
90
0C
Press PAUSE (Write) button.
Click on the first or last page to see other DCR-VX2200E (serv.man2) service manuals if exist.