Read Sony DCR-TRV130 / DCR-TRV130E / DCR-TRV230 / DCR-TRV230E / DCR-TRV235E / DCR-TRV325E / DCR-TRV330 / DCR-TRV330E / DCR-TRV430E / DCR-TRV530 / DCR-TRV530E / DCR-TRV725E / DCR-TRV730 / DCR-TRV730E / DCR-TRV828 / DCR-TRV828E / DCR-TRV830 / DCR-TRV830E Service Manual online
— 13 —
3-2. Cassette compartment assembly
1. Removal procedure
1)
Set the [EJ] mode to move up the cassette compartment
assembly 0.
assembly 0.
2)
Remove the capstan flexible board and flexible wiring board
(FP-300) 1 from the holders X, Y and Z in the directions
of the arrows A, B and C.
(FP-300) 1 from the holders X, Y and Z in the directions
of the arrows A, B and C.
3)
Push the damper assembly 3 in the directions of the arrows
D
D
and E and remove it from the notch of the LS chassis block
assembly.
4)
Remove the two screws (camera pan2 main M1.4
×
1.6) 4.
5)
With the cassette compartment assembly 0 half opened, move
the face plate in the direction of the arrow F and remove it
from the grooves 6 and 7 on the LS chassis block assembly.
the face plate in the direction of the arrow F and remove it
from the grooves 6 and 7 on the LS chassis block assembly.
6)
Remove the cassette holder (S) 8 and cassette holder (T) 9
of the cassette compartment assembly 0 from the groove on
the LS chassis block assembly.
of the cassette compartment assembly 0 from the groove on
the LS chassis block assembly.
2. Attachment procedure
1)
Set the [USE] mode.
2)
Insert the cassette holder (S) 8 of the cassette compartment
assembly 0 and cassette holder (T) 9 into the grooves on
both sides of the LS chassis block assembly.
assembly 0 and cassette holder (T) 9 into the grooves on
both sides of the LS chassis block assembly.
3)
While moving down the cassette compartment assembly 0,
lift up the face plate in the direction of the arrow F and keep
this status. Then, insert the face plate in the grooves 6 and 7
on the LS chassis block assembly.
lift up the face plate in the direction of the arrow F and keep
this status. Then, insert the face plate in the grooves 6 and 7
on the LS chassis block assembly.
4)
Tighten the two screws (camera pan2 main M1.4
×
1.6) 4.
Tightening torque: 0.078
±
0.01 N•m (0.8
±
0.1 kgf•cm)
5)
Move the damper arm of the damper assembly 3 to the 4
o’clock position and insert the damper assembly into the hole
on the LS chassis block assembly and the dowel of the cassette
holder (T) 9.
o’clock position and insert the damper assembly into the hole
on the LS chassis block assembly and the dowel of the cassette
holder (T) 9.
6)
Align the damper assembly 3 with the notch of the LS chassis
block assembly and rotate the damper assembly 3 in the
opposite direction to the arrow E to fix it.
block assembly and rotate the damper assembly 3 in the
opposite direction to the arrow E to fix it.
Fig. 3-2
0
Cassette compartment
assembly
Cassette holder (T)
Cassette holder (S)
4
Two screws
(camera pan 2 main M1.4
×
1.6)
5
Remove the cassette
compartment assembly
in the direction of the
arrow
in the direction of the
arrow
F
.
6
8
7
F
Face plate
9
While pressing
toward the inside
toward the inside
While pressing
toward the inside
toward the inside
*
Be careful not to
deform here.
*
Be careful not to
deform here.
Apply grease.
2
Remove the damper assembly in the
direction of the arrow
E
.
Insert into these holes
and attach.
and attach.
Push
Cassette holder (T)
D
E
B
C
A
X
Y
Z
Remove the flexible board in the
direction of the arrow
direction of the arrow
A
B
C
.
1
FP-300 flexible board,
Capstan flexible board
FP-300 flexible board
3
Damper assembly
Damper arm
Move the damper arm
to the 4 o'clock position.
to the 4 o'clock position.
Capstan flexible board
Damper
assembly
assembly
When attaching it, coat the hatched portion with grease.
Click on the first or last page to see other DCR-TRV130 / DCR-TRV130E / DCR-TRV230 / DCR-TRV230E / DCR-TRV235E / DCR-TRV325E / DCR-TRV330 / DCR-TRV330E / DCR-TRV430E / DCR-TRV530 / DCR-TRV530E / DCR-TRV725E / DCR-TRV730 / DCR-TRV730E / DCR-TRV828 / DCR-TRV828E / DCR-TRV830 / DCR-TRV830E service manuals if exist.